• Acts as an additional protective layer
• Recommended for extremely dusty conditions
• Premature sanding of the air filter is avoided
• Coarse-pored air filter cover

• Approvals: CCCUO_EU
• Colour: White

• Recommended for extremely dusty conditions

• Approvals: CCCUO_EU

• Recommended in extremely wet conditions.

• Approvals: CCCUO_EU

• CNC milled from high-strength solid aluminum
• Chrome-plated pad guide pins on the brake caliper
• The benefits:
  
  • Reduced brake pad canting, hence no uneven wear
  • Constant braking feel, irrespective of brake pad wear or temperature
  • No vibration from the brake

Fitting possible on SX/EXC models without adapter, with the original hand pump and brake hose.
Can only be fitted with a 17"or 16.5" front wheel. 310 mm brake disc 586.09.060.000 or 250.09.260.000 required.
In combination with brake disc 25009260000 (310 mm) no speedometer signal will be sent.

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• High stiffness and strength
• Made of high-quality carbon
• Optimal protection against stone impact
• Visual highlight
• Optimal protection against stone impact

• Approvals: HOMNN_EU
• Surface (PowerParts): Matte finish
• Material (PowerParts): Carbon

• Clear pressure point across the entire temperature range
• More brake power
• Higher stiffness with the same weight
• Made of high-strength aluminum

• Approvals: CCCUO_EU
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Aluminium
• Alignment: Rear

• Clear pressure point across the entire temperature range
• More brake power
• Higher stiffness with the same weight
• Made of high-strength aluminum

• Approvals: CCCUO_EU
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Aluminium
• Alignment: Front

• Outer ring made of stainless high-performance brake steel
• Larger diameter for added braking performance

• Approvals: CCCUO_EU
• Diameter: 320 mm
• Material (PowerParts): Stainless steel

• No fading
• Outer ring made of stainless high-performance brake steel
• Minimal wear on brake pads
• Significantly longer lasting
• With Flame design for added braking performance

• Approvals: ABE
• Diameter: 220
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Stainless steel
• Alignment: Rear

• Floating
• Outer ring made of stainless high-performance brake steel
• Minimal wear on brake pads
• With Flame design for added braking performance

• Approvals: ABE
• Colour: Black
• Diameter: 260
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Aluminium

• Floating
• Outer ring made of stainless high-performance brake steel
• Inner ring anodised
• Minimal wear on brake pads
• With Flame design for added braking performance

• Up to 20% weight saving compared to stock components;
• Incl. the required CNC machined, black anodized brake caliper support for Brembo brake systems

• Approvals: ABE
• Colour: Black
• Diameter: 270 mm
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Front

• Floating
• Outer ring made of stainless high-performance brake steel
• Inner ring anodised
• Minimal wear on brake pads

• Approvals: EC-V
• Colour: Black
• Diameter: 260 mm
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Front

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Approvals: CCCUO_EU
• Material (PowerParts): Organic
• Alignment: Front

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

• Approvals: CCCUO_EU
• Material (PowerParts): Sinter
• Alignment: Front

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

• Approvals: CCCUO_EU
• Material (PowerParts): Sinter
• Alignment: Rear

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Approvals: CCCUO_EU
• Material (PowerParts): Organic
• Alignment: Rear

• With return valve
• Anodised dust protection cap
• Quick and easy bleeding of the brake

• Approvals: HOMNN_EU
• Colour: Orange
• Material (PowerParts): Aluminium
• Alignment: Front

• With return valve
• Anodised dust protection cap
• Quick and easy bleeding of the brake

• Approvals: HOMNN_EU
• Colour: Orange
• Material (PowerParts): Aluminium
• Alignment: Front

• Made of high-strength aluminum
• Improved braking performance

• Only for Brembo brake systems.
• Required for using the 320 mm brake disc 58309060000 with Brembo brake caliper

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• Manufactured using state-of-the-art 2-component injection molding technology
• Extremely light
• Protects the brake disc from stones and other solid obstacles
• Central adapter replaces the spacer sleeve on the wheel axle
• Allows tyre changes, brake service etc. without removing the brake cover

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic
• Alignment: Front

• Made of high-quality carbon
• Protects the rear brake disc from stones and other solid obstacles

• Approvals: HOMNN_EU
• Surface (PowerParts): Glossy finish
• Material (PowerParts): Carbon
• Alignment: Rear

• Manufactured using state-of-the-art 2-component injection molding technology
• Extremely light
• Protects the brake disc from stones and other solid obstacles
• Central adapter replaces the spacer sleeve on the wheel axle
• Allows tyre changes, brake service etc. without removing the brake cover
• Noble material mix of carbon fiber and plastic

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Carbon

• Allows the rear wheel to be braked with the left hand
• Provides additional control in critical riding situations
• For use with the automatic clutch

• Only fits for Brembo and Magura brake systems
• To mount it on Braketec 70013071000 have to be used.

• Approvals: CCCUO_EU

• Protects the brake pedal from bending by branches

• Approvals: HOMNN_EU

• Perfect fit
• Made of high-quality carbon
• Optimal protection against stone impact

• Only for Brembo systems

• Approvals: HOMNN_EU
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Carbon

• For all 48 mm forks
• Made of high-quality carbon

• Approvals: HOMNN_EU
• Material (PowerParts): Carbon

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability
• Visual highlight

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Electronic orange

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability
• Visual highlight

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Gold

• Greater flexibility and better running characteristics
• Constant and permanent lubrication
• Better sealing against water and dirt
• Significantly longer durability

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Black

• Greater flexibility and better running characteristics
• Constant and permanent lubrication
• Better sealing against water and dirt
• Significantly longer durability

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Electronic orange

In orange Factory look.

• Approvals: HOMNN_EU
• Colour: Orange
• Alignment: Bottom

• Approvals: HOMNN_EU
• Colour: Orange

• Visual highlight
• Race look

• Approvals: HOMNN_EU
• Colour: Black

• Highest quality workmanship
• The right combination of look, style, and performance
• Specially designed for the challenges of off-road use
• Made from special, high-strength plastic for maximum stability
• With exchangeable chain track surface, therefore extremely durable

• Approvals: HOMNN_EU

• Prevents the chain from hitting the rear tyre
• Perfect chain guide, no branches drawn in between chain and engine housing

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Race look
• Visual highlight
• With exchangeable chain track surface, therefore extremely durable
• Specially designed for the challenges of off-road use

• CNC machined out of teflon

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING

• With exchangeable chain track surface, therefore extremely durable
• Specially designed for the challenges of off-road use
• Visual highlight
• Race look

• Approvals: HOMNN_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING

• Resistant to the toughest stresses and strains
• Forged lightening indents reduce rotational mass
• Grooves between the teeth clear dirt under the chain
• Extends chain life

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Steel
• Number Of Teeth: 13 teeth

• Significantly longer durability
• Teeth made of high-strength steel, for an extra long service life
• Extremely low-wear
• Recommended for long journeys

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Steel
• Number Of Teeth: 49 teeth

• Specially designed for the challenges of off-road use
• Significantly longer durability
• Made of high-strength aluminum
• The right combination of look, style, and performance

• The lightest Renthal Sprocket on the market
• Provide maximum power transfer and long-life due to advanced tooth profile and perfect concentricity
• Combination of a high strength base material and exceptionally hardwearing surface

• Approvals: HOMNN_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Number Of Teeth: 45 teeth

• Specially designed for the challenges of off-road use
• Significantly longer durability
• Made of high-strength aluminum
• The right combination of look, style, and performance

• The lightest Renthal Sprocket on the market
• Provide maximum power transfer and long-life due to advanced tooth profile and perfect concentricity
• Combination of a high strength base material and exceptionally hardwearing surface

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Number Of Teeth: 44 teeth

• Teeth made of high-strength steel, for an extra long service life
• Aluminum center section, reduces unsprung masses
• Permanently joined together with high-strength rivets
• At least three times longer service life than other aluminum rear sprockets
• 50 % lighter than steel rear sprockets
• Longer service life of the entire drivetrain kit

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Number Of Teeth: 46 teeth

• Teeth made of high-strength steel, for an extra long service life
• Aluminum center section, reduces unsprung masses
• Permanently joined together with high-strength rivets
• At least three times longer service life than other aluminum rear sprockets
• 50 % lighter than steel rear sprockets
• Longer service life of the entire drivetrain kit

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Number Of Teeth: 50 teeth

• Provides more traction when starting
• Made of high-strength aluminum
• Elegant anodised surface
• Pure race feeling
• Mounted directly on the OEM-fork

• Two different selectable preloads, without additional effort in mounting
• Simple mounting of the fork ring due to two part design
• No longer necessary to remove the fork

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Easy to mount
• Protects the linkage from damage

• Approvals: HOMNN_EU

• Elegant anodised surface
• Visual highlight
• CNC milled aluminum triple clamp
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility – precisely customised to the WP fork
• Specially optimised geometry of the fork clamping
• No ovalization of the fork outer tube
• Highly precise and smooth fork response
• Maximum handling gain
• Gain in stability at the front wheel
• Overall, more homogeneous force flows in the entire vehicle
• Simple offset adjustment
• Including steering stem with steering head bearing already pressed on

• Very simple offset adjustment of 20 or 22 mm
• Shorter offset: Stability on fast straights
• Longer offset: easier and quicker cornering in curves

Color differences between the upper and lower triple clamp cannot be technically ruled out.

• Approvals: CCCUO_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

Color differences between the upper and lower triple clamp cannot be technically ruled out.

• Elegant anodised surface
• Visual highlight
• CNC milled aluminum triple clamp
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility – precisely customised to the WP fork
• Including steering stem with steering head bearing already pressed on

• Handlebar mount kit 78901939044/144/244/344/444 or
• PHDS SXS07125200

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Offset: 20

Color differences between the upper and lower triple clamp cannot be technically ruled out.

• Elegant anodised surface
• Visual highlight
• CNC milled aluminum triple clamp
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility – precisely customised to the WP fork
• Including steering stem with steering head bearing already pressed on

• Handlebar mount kit 78901939044/144/244/344/444 or
• PHDS SXS07125200

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Offset: 22

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Front

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Rear

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Easy to mount
• Visual highlight
• Suitable for the left and right side

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight

• +8 mm at 125/150 SX/XC-W, SX-F, 450/500 EXC-F
• +16 mm at 250/300 SX/EXC, 250/350 EXC-F

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Includes drilling for safety wire
• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight
• Includes drilling for safety wire

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Approvals: HOMNN_EU
• Colour: Orange
• Material (PowerParts): Silicone

• Protects the radiator from mud, dirt and sand
• Protection against rapid overheating of the engine in muddy conditions
• For extremely muddy conditions

• Approvals: HOMNN_EU

• Provides maximum protection at the lowest possible weight
• Including adapted radiator protection grills
• Easy to mount
• Optimal protection against stone impact

• Approvals: HOMNN_EU
• Colour: Black

• Suitable for the left and right side
• Provides maximum protection at the lowest possible weight
• Optimal protection against stone impact
• Easy to mount

• Approvals: HOMNN_EU
• Colour: White

• Protects the radiator from mud, dirt and sand
• Protection against rapid overheating of the engine in muddy conditions
• For extremely muddy conditions

• Approvals: HOMNN_EU

• All required parts for converting your 250 to a 300 Motocross.

• Approvals: CCCUO_EU

• Improves clutch performance and durability
• Hinson-typical surface treatment for significantly improved robustness compared to the standard part
• Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled
• Can be installed in the standard clutch or in combination with other Hinson clutch components
• CNC milled from high-strength aluminum
• Improves heat dissipation

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Improves clutch performance and durability
• Hinson-typical surface treatment for significantly improved robustness compared to the standard part
• Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled
• Can be installed in the standard clutch or in combination with other Hinson clutch components
• CNC milled from high-strength aluminum
• Improves heat dissipation

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Uncompromising race look
• CNC milled from high-strength aluminum
• Resistant to the toughest stresses and strains
• Elegant anodised surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Installed in the standard clutch, which means simple, uncomplicated and fast installation
• Unlimited and total concentration on the perfect line
• New generation of Rekluse centrifugal clutch with EXP technology
• Easily adjustable from the outside via the clutch slave cylinder
• No stalling of the engine in critical situations, such as braking, downhill runs, jumping, or when starting or pushing
• Improved traction, controllable by the throttle alone
• Slippery, extremely steep sections can be managed more easily > saves time and ensures faster lap times
• More relaxed, fatigue-free and controlled riding, even over longer distances and in tough terrain
• No more coupling is required, although it is still possible
• Special rear brake conversion kit available, allowing braking of the rear wheel with the left hand
• Tested in the toughest conditions

• Approvals: HOMNN_EU

• Made from high grade titanium
• Uncompromising race look
• Permanently welded brackets
• Complies with current FIM noise regulations
• Significantly more torque
• Significantly more performance
• Substantial weight saving
• Akrapovič logo sticker on silencer

• Approvals: CCCUO_EU
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Titanium

• Extra strong sheet steel
• Nickel-plated surface
• Wide, even engine speed range
• Higher speed
• More traction
• Better gas control

• Approvals: CCCUO_EU
• Surface (PowerParts): Nickelplated
• Material (PowerParts): Stainless steel

• Silencer housing made of high-grade aluminum
• Rich sound
• Low noise level
• Easy to mount
• Perfect fit
• Reduced weight
• Specially developed for enduro use

• Approvals: CCCUO_EU
• Colour: Black
• Material (PowerParts): Aluminium

• High stiffness and strength
• 80 % lighter than steel with the same load-bearing capacity
• Elegant look
• Low thermal expansion
• Made of high-quality carbon
• High long-term temperature stability
• Non-corrosive
• Maximum protection against falls, flying stones, branches, etc.
• Can only be fitted with a standard header

• Approvals: HOMNN_EU
• Surface (PowerParts): Glossy finish
• Material (PowerParts): Carbon

• More curve pressure
• Permanent contact between boot and footpeg
• Extends the service life of your boots
• Enlarged tread area
• More control
• Easier shifting and braking
• Move along with weight shift

• Approvals: CCCUO_EU

• Coated neoprene ring
• Simply pulled over the grips

• Approvals: HOMNN_EU
• Colour: Orange

• Made of high-strength aluminum
• Specially developed for extreme conditions
• Makes it easier to stand your motorcycle up

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Developed according to the requirements of our factory drivers
• Less stress when riding
• Objective: comfort AND safety
• Ergonomic contour adapted to the shape of the hand for maximum comfort
• Half waffle grip
• For a secure grip
• Three areas for the metal wire locking
• Version: medium

• Approvals: HOMNN_EU
• Colour: Grey
• Note: Closed end

• Developed according to the requirements of our factory drivers
• Less stress when riding
• Objective: comfort AND safety
• Ergonomic contour adapted to the shape of the hand for maximum comfort
• Half waffle grip
• For a secure grip
• Three areas for the metal wire locking
• Version: soft

• Approvals: HOMNN_EU
• Colour: Grey
• Note: Closed end

• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• Approvals: HOMNN_EU
• Colour: Grey
• Note: Open end

• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• Approvals: HOMNN_EU
• Colour: Black
• Note: Open end

• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• Approvals: HOMNN_EU
• Colour: Black
• Note: Closed end

• For a secure grip
• Maximum grip on the hand grip even in extremely muddy conditions

• Approvals: HOMNN_EU
• Colour: Black

• Makes it easier to stand your motorcycle up
• Specially developed for extreme conditions
• Strap made from high-strength nylon

• Approvals: HOMNN_EU
• Colour: Black
• Alignment: Front

• Specially developed for extreme conditions
• Strap made from high-strength nylon
• Makes it easier to stand your motorcycle up

• High-strength nylon strap
• Indispensable for use on extreme terrain
• Makes it easy to get your bike upright
• Attaches to rear frame

• Approvals: HOMNN_EU
• Colour: Black
• Alignment: Rear

• A motorcycle hand grip can be mounted on the handle (not included)

• Approvals: HOMNN_EU

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Attached directly at the levers with a special mounting

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Attached directly at the levers with a special mounting
• Only mountable with Brembo brake system

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Attached directly at the levers with a special mounting
• Only mountable with Brembo brake system

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Attached directly at the levers with a special mounting
• Only mountable with Brembo brake system

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Recommended for use in conjunction with radial hand brake cylinders
• More distance between brake/clutch lever and handguard

• Approvals: HOMNN_EU

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design

• Attached directly at the levers with a special mounting.
• Only mountable with Brembo brake system

• Approvals: HOMNN_EU
• Colour: Orange
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design

• Attached directly at the levers with a special mounting.
• Only mountable with Brembo brake system

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design

• Approvals: HOMNN_EU
• Colour: White
• Material (PowerParts): Plastic

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Excellent weather protection
• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers

• Approvals: HOMNN_EU
• Colour: White
• Material (PowerParts): Aluminium

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Excellent weather protection
• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic
• Excellent weather protection

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Excellent weather protection
• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Ceramic white
• Material (PowerParts): Plastic

• Excellent weather protection
• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Ceramic white
• Material (PowerParts): Aluminium

• Never again cold fingers!
• Mounting over handlebar and switches
• Better control during winter ride-outs

• Approvals: HOMNN_EU

• Extremely sturdy aluminum brackets
• Prevents broken levers
• Including all required assembly materials

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• Made of robust plastic
• To convert the open, standard handguards to a closed version

• Usable with handguards 7960297900028/30AB and 2650297900028/30/AB

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Extremely sturdy aluminum brackets
• Prevents broken levers
• Including all required assembly materials

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Made of robust plastic
• Fastening independent of fittings directly on the handlebars
• To convert the open, standard handguards to a closed version

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Made of robust plastic
• Fastening independent of fittings directly on the handlebars
• To convert the open, standard handguards to a closed version

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Made of robust plastic
• Fastening independent of fittings directly on the handlebars
• To convert the open, standard handguards to a closed version

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Made of robust plastic
• Fastening independent of fittings directly on the handlebars
• To convert the open, standard handguards to a closed version

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Approvals: CCCUO_EU
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Height (PowerParts): 51

• Conversion of the standard damped handlebar mount into a rigid one

• Approvals: HOMNN_EU
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled handlebar mount with damping rubber inserts
• Gentle on wrists and shoulder joints
• Damping of hard shocks
• Absorption of chassis and engine vibrations
• Additional handlebar damping in horizontal direction
• Optimum steering precision
• Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment
• Replaces the standard damping rubbers used in the handlebar mount

• Approvals: CCCUO_EU
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled handlebar mount with damping rubber inserts
• Gentle on wrists and shoulder joints
• Damping of hard shocks
• Absorption of chassis and engine vibrations
• Additional handlebar damping in horizontal direction
• Optimum steering precision
• Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment

• Handlebar height adjustable to 2 positions

• Approvals: EC-V
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Made of high-strength aluminum
• Tested in complex and specially-developed test cycles
• Position markings for easy adjustment

• Dimensions: A = 115 mm, B = 806 mm, C = 62 mm

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• When locked, the crossbar is solid (stiff)
• When unlocked, the crossbar is flexible

Dimensions: A = 112 mm, B = 811 mm, C = 88 mm

• Approvals: CCCUO_EU
• Diameter: 28 mm
• Factory Racing: USED BY FACTORY RACING

• Two handlebars in one
• The exterior ensures maximum resistance to external damage (e.g. fall)
• Additionally hard anodised against corrosion
• The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls.
• Nylon inserts in the inner tube allow thinner walls
• Very good flex properties
• Comes with handlebar pad

Renthal Twinwall 996

• Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

• Approvals: CCCUO_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• The Twinwall, in the KTM orange design
• Two handlebars in one
• The exterior ensures maximum resistance to external damage (e.g. fall)
• Additionally hard anodised against corrosion
• The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls.
• Nylon inserts in the inner tube allow thinner walls
• Very good flex properties
• Comes with handlebar pad

• Dimensions: A = 104 mm, B = 811 mm, C = 74 mm

• Approvals: CCCUO_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• The Twinwall, in the KTM orange design
• Two handlebars in one
• The exterior ensures maximum resistance to external damage (e.g. fall)
• Additionally hard anodised against corrosion
• The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls.
• Nylon inserts in the inner tube allow thinner walls
• Very good flex properties
• Comes with handlebar pad

• Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

• Approvals: CCCUO_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Enables power consumers such as grip heater or radiator fans to be installed on motocross or cross-country models as well

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU

• Ignition curve adjustment made easy!
• Comfortable ignition curve adjustment on the handlebar

• Approvals: CCCUO_EU

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight with technical and ergonomic added value
• Adjustable grip width

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight with technical and ergonomic added value
• Ergonomically perfect shape (the result of years of racing experience)
• Adjustable grip width

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Weight: 0.055

• Elegant anodised surface
• Visual highlight with technical and ergonomic added value
• Flaps removed on ground contact
• Prevents broken levers

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Elegant anodised surface
• Visual highlight with technical and ergonomic added value
• Flaps removed on ground contact
• Prevents broken levers

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight
• Including plastic insert
• Reduces the risk of a lever being broken

Suitable for all Brembo® and Formula brake and clutch assembles

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight
• Prevents the hand grips from chafing in the event of a fall

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium