• Acts as an additional protective layer
• Recommended for extremely dusty conditions
• Premature sanding of the air filter is avoided
• Coarse-pored air filter cover
• Washable

• Approvals: CCCUO_EU

• Recommended for extremely dusty conditions
• Acts as an additional protective layer
• Extends the filter service intervals
• Premature sanding of the air filter is avoided

• Approvals: CCCUO_EU

• Recommended in extremely wet conditions.
• Acts as an additional protective layer
• Washable

• Approvals: CCCUO_EU

• High stiffness and strength
• Made of high-quality carbon
• Optimal protection against stone impact
• Visual highlight

• Approvals: HOMNN_EU
• Surface (PowerParts): Matte finish
• Material (PowerParts): Carbon

• Clear pressure point across the entire temperature range
• More brake power
• Higher stiffness with the same weight
• Made of high-strength aluminum

• Approvals: CCCUO_EU
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Aluminium
• Alignment: Rear

• Clear pressure point across the entire temperature range
• More brake power
• Higher stiffness with the same weight
• Made of high-strength aluminum

• Approvals: CCCUO_EU
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Aluminium
• Alignment: Front

• Outer ring made of stainless high-performance brake steel
• Larger diameter for added braking performance

• Approvals: CCCUO_EU
• Diameter: 320 mm
• Material (PowerParts): Stainless steel

• Floating
• Outer ring made of stainless high-performance brake steel
• Minimal wear on brake pads
• With Flame design for added braking performance

• Approvals: ABE
• Colour: Black
• Diameter: 260
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Aluminium

• No fading
• Outer ring made of stainless high-performance brake steel
• Minimal wear on brake pads
• Significantly longer lasting
• With Flame design for added braking performance

• Approvals: ABE
• Diameter: 220 mm
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Stainless steel
• Alignment: Rear

• Floating
• Outer ring made of stainless high-performance brake steel
• Inner ring anodised
• Minimal wear on brake pads
• With Flame design for added braking performance

• Up to 20% weight saving compared to stock components;
• Incl. the required CNC machined, black anodized brake caliper support for Brembo brake systems

• Approvals: ABE
• Colour: Black
• Diameter: 270 mm
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Front

• Minimal wear on brake pads
• Significantly longer lasting
• Full version for muddy track conditions

• Approvals: CCCUO_EU
• Diameter: 220 mm
• Material (PowerParts): Stainless steel

• Floating
• Outer ring made of stainless high-performance brake steel
• Inner ring anodised
• Minimal wear on brake pads

• Approvals: EC-V
• Colour: Black
• Diameter: 260 mm
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Front

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Approvals: CCCUO_EU
• Material (PowerParts): Organic
• Alignment: Front

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

• Approvals: CCCUO_EU
• Material (PowerParts): Sinter
• Alignment: Rear

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Approvals: CCCUO_EU
• Material (PowerParts): Organic
• Alignment: Rear

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

• Approvals: CCCUO_EU
• Material (PowerParts): Sinter
• Alignment: Front

• With return valve
• Anodised dust protection cap
• Quick and easy bleeding of the brake

• Approvals: HOMNN_EU
• Colour: Orange
• Material (PowerParts): Aluminium
• Alignment: Front

• With return valve
• Anodised dust protection cap
• Quick and easy bleeding of the brake

• Approvals: HOMNN_EU
• Colour: Orange
• Material (PowerParts): Aluminium
• Alignment: Front

• Made of high-strength aluminum
• Improved braking performance

• Only for Brembo brake systems.
• Required for using the 320 mm brake disc 58309060000 with Brembo brake caliper

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• High stiffness and strength
• CNC milled from high-strength aluminum
• Lighter than series components
• Improved braking performance

• Approvals: CCCUO_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Protects the brake disc in the event of a fall
• High stiffness and strength
• Protects the rear brake disc from stones and other solid obstacles
• CNC milled from high-strength aluminum
• Lighter than series components
• Improved braking performance

• Approvals: CCCUO_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Rear

• Protects the brake disc in the event of a fall
• High stiffness and strength
• Protects the rear brake disc from stones and other solid obstacles
• CNC milled from high-strength aluminum
• Lighter than series components
• Improved braking performance

• Approvals: CCCUO_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Rear

• Protects the brake disc in the event of a fall
• High stiffness and strength
• Protects the rear brake disc from stones and other solid obstacles
• CNC milled from high-strength aluminum
• Lighter than series components

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Rear

• Manufactured using state-of-the-art 2-component injection molding technology
• Extremely light
• Protects the brake disc from stones and other solid obstacles
• Central adapter replaces the spacer sleeve on the wheel axle
• Allows tyre changes, brake service etc. without removing the brake cover

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic
• Alignment: Front

• Manufactured using state-of-the-art 2-component injection molding technology
• Extremely light
• Protects the brake disc from stones and other solid obstacles
• Central adapter replaces the spacer sleeve on the wheel axle
• Allows tyre changes, brake service etc. without removing the brake cover
• Noble material mix of carbon fiber and plastic

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Carbon

• Increases the volume of the rear master cylinder
• Additional cooling ribs minimise the heating of the brake fluid
• Eliminates “fading” almost completely

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Rear

• Protects the brake pedal from bending by branches

• Approvals: HOMNN_EU

• Protects the brake pedal from bending by branches

• Approvals: HOMNN_EU

• Perfect fit
• Made of high-quality carbon
• Optimal protection against stone impact

• Only for Brembo systems

• Approvals: HOMNN_EU
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Carbon

• For all 48 mm forks
• Made of high-quality carbon

• Approvals: HOMNN_EU
• Material (PowerParts): Carbon

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Black

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Gold

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Electronic orange

• Greater flexibility and better running characteristics
• Constant and permanent lubrication
• Better sealing against water and dirt
• Significantly longer durability

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Electronic orange

• Greater flexibility and better running characteristics
• Constant and permanent lubrication
• Better sealing against water and dirt
• Significantly longer durability

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Black

• Perfect for changing the look of your motorcycle

• Approvals: HOMNN_EU
• Colour: Orange
• Alignment: Bottom

• With exchangeable chain track surface, therefore extremely durable
• Developed for use on the toughest off-road terrain
• Developed according to the requirements of our factory drivers
• Race look

• Approvals: HOMNN_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING

• Race look

• Approvals: HOMNN_EU
• Colour: Orange

• Elegant look

• Approvals: HOMNN_EU
• Colour: Orange

• Significantly longer durability
• Teeth made of high-strength steel, for an extra long service life
• Extremely low-wear
• Recommended for long journeys

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Steel
• Number Of Teeth: 49 teeth

• Resistant to the toughest stresses and strains
• Forged lightening indents reduce rotational mass
• Grooves between the teeth clear dirt under the chain
• Extends chain life

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Steel
• Number Of Teeth: 13 teeth

• Specially designed for the challenges of off-road use
• Significantly longer durability
• Made of high-strength aluminum
• The right combination of look, style, and performance

• The lightest Renthal Sprocket on the market
• Provide maximum power transfer and long-life due to advanced tooth profile and perfect concentricity
• Combination of a high strength base material and exceptionally hardwearing surface

• Approvals: HOMNN_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Number Of Teeth: 45 teeth

• Specially designed for the challenges of off-road use
• Significantly longer durability
• Made of high-strength aluminum
• The right combination of look, style, and performance

• The lightest Renthal Sprocket on the market
• Provide maximum power transfer and long-life due to advanced tooth profile and perfect concentricity
• Combination of a high strength base material and exceptionally hardwearing surface

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Number Of Teeth: 44 teeth

• Teeth made of high-strength steel, for an extra long service life
• Aluminum center section, reduces unsprung masses
• Permanently joined together with high-strength rivets
• At least three times longer service life than other aluminum rear sprockets
• 50 % lighter than steel rear sprockets
• Longer service life of the entire drivetrain kit

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Number Of Teeth: 45 teeth

• Teeth made of high-strength steel, for an extra long service life
• Aluminum center section, reduces unsprung masses
• Permanently joined together with high-strength rivets
• At least three times longer service life than other aluminum rear sprockets
• 50 % lighter than steel rear sprockets
• Longer service life of the entire drivetrain kit

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Number Of Teeth: 45 teeth

• Specially developed for WP forks
• Fork bleeding using finger pressure
• Developed together with the vehicle

• Approvals: HOMNN_EU

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Robust, solid construction

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Made of the highest quality materials
• Tested in the toughest conditions
• Developed together with the vehicle
• Enables shorter drivers to also achieve the optimum seat height
• Perfect compromise between maximum chassis performance and lowest possible vehicle height
• No restrictions on riding dynamics

• Approvals: CCCUO_EU
• Height (PowerParts): -50

• Made of the highest quality materials
• Tested in the toughest conditions
• Developed together with the vehicle
• Enables shorter drivers to also achieve the optimum seat height
• Perfect compromise between maximum chassis performance and lowest possible vehicle height
• No restrictions on riding dynamics

• Approvals: CCCUO_EU
• Height (PowerParts): -20

• Fast preload adjustment
• Use of the entire length of the thread on the shock absorber
• Very easy operation
• Extremely low weight
• Dirt-resistance
• Mechanical drive

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Made of the highest quality materials
• CNC milled from high-strength aluminum
• High-quality look
• Toolless adjustment of the spring preload

• Toolless adjustment of the reservoir spring prelaod
• Enables the adjustment of the "Ride Balance"
• More preload on the reservoir spring = more oil pressure = more hold-up
• No loss of comfort with more preload

For removal of Preload adjuster tool T12141 should be used.

• Approvals: HOMNN_EU
• Colour: Red
• Surface (PowerParts): Anodized

• Provides more traction when starting
• Made of high-strength aluminum
• Elegant anodised surface
• Pure race feeling
• Mounted directly on the OEM-fork

• Two different selectable preloads, without additional effort in mounting
• Simple mounting of the fork ring due to two part design
• No longer necessary to remove the fork

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Provides more traction when starting
• Made of high-strength aluminum
• Elegant anodised surface
• Pure race feeling
• Mounted directly on the OEM-fork

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

Color differences between the upper and lower triple clamp cannot be technically ruled out.

• CNC milled aluminum triple clamp
• Elegant anodised surface
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility – precisely customised to the WP fork
• Specially optimised geometry of the fork clamping
• No ovalization of the fork outer tube
• Highly precise and smooth fork response
• Maximum handling gain
• Gain in stability at the front wheel
• Overall, more homogeneous force flows in the entire vehicle
• Simple offset adjustment
• Including steering stem with steering head bearing already pressed on

• Very simple offset adjustment of 20 or 22 mm
• Shorter offset: Stability on fast straights
• Longer offset: easier and quicker cornering in curves

Color differences between the upper and lower triple clamp cannot be technically ruled out.

• Approvals: CCCUO_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

Color differences between the upper and lower triple clamp cannot be technically ruled out.

• CNC milled aluminum triple clamp
• Elegant anodised surface
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility – precisely customised to the WP fork
• Specially optimised geometry of the fork clamping
• No ovalization of the fork outer tube
• Highly precise and smooth fork response
• Maximum handling gain
• Gain in stability at the front wheel
• Overall, more homogeneous force flows in the entire vehicle
• Simple offset adjustment
• Including steering stem with steering head bearing already pressed on

• Very simple offset adjustment of 20 or 22 mm
• Shorter offset: Stability on fast straights
• Longer offset: easier and quicker cornering in curves

Color differences between the upper and lower triple clamp cannot be technically ruled out.

• Approvals: CCCUO_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Elegant anodised surface
• CNC milled aluminum triple clamp
• Including steering stem with steering head bearing already pressed on

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Front

• CNC milled from high-strength aluminum
• Elegant anodised surface

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Rear

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface

• +8 mm at 125/150 SX/XC-W, SX-F, 450/500 EXC-F
• +16 mm at 250/300 SX/EXC, 250/350 EXC-F

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface

• Approvals: HOMNN_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• The weight-optimised water pump cover ensures maximum water flow
• CNC milled from high-strength aluminum
• Elegant anodised surface

• Approvals: HOMNN_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Includes drilling for safety wire

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Includes drilling for safety wire

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Protects the radiator from mud, dirt and sand
• Protection against rapid overheating of the engine in muddy conditions
• For extremely muddy conditions

• Approvals: HOMNN_EU

• Protects the radiator hose in case of a hit to the front wheel during full steering angle

• Approvals: HOMNN_EU

• Provides maximum protection at the lowest possible weight
• Optimal protection against stone impact
• Easy to mount

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Provides maximum protection at the lowest possible weight
• Optimal protection against stone impact
• Easy to mount

• Approvals: HOMNN_EU
• Colour: Orange
• Material (PowerParts): Plastic

• Provides maximum protection at the lowest possible weight
• Optimal protection against stone impact
• Easy to mount

• Approvals: HOMNN_EU
• Colour: White
• Material (PowerParts): Plastic

• Protects the radiator from mud, dirt and sand
• Protection against rapid overheating of the engine in muddy conditions

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU
• Colour: Black

• Provides more air
• Maximum performance
• Digital control
• Current temperature can be read at any time
• Variable switch-on temperature between 65 °C and 95 °C
• Switch-off temperature 1 °C below the selected switch-on temperature
• Provides better cooling of the engine

• Approvals: HOMNN_EU

• Better cooling
• Maximum performance
• Provides more air
• Plug & Play mounting

• Approvals: HOMNN_EU

• Improves clutch performance and durability
• Hinson-typical surface treatment for significantly improved robustness compared to the standard part
• Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled
• Can be installed in the standard clutch or in combination with other Hinson clutch components
• CNC milled from high-strength aluminum
• Improves heat dissipation

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Resistant to the toughest stresses and strains
• Weight-optimised

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Improves clutch performance and durability
• Hinson-typical surface treatment for significantly improved robustness compared to the standard part
• Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled
• Can be installed in the standard clutch or in combination with other Hinson clutch components
• CNC milled from high-strength aluminum
• Improves heat dissipation

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Installed in the standard clutch, which means simple, uncomplicated and fast installation
• Unlimited and total concentration on the perfect line
• New generation of Rekluse centrifugal clutch with EXP technology
• Easily adjustable from the outside via the clutch slave cylinder
• No stalling of the engine in critical situations, such as braking, downhill runs, jumping, or when starting or pushing
• Improved traction, controllable by the throttle alone
• Slippery, extremely steep sections can be managed more easily > saves time and ensures faster lap times
• More relaxed, fatigue-free and controlled riding, even over longer distances and in tough terrain
• No more coupling is required, although it is still possible
• Special rear brake conversion kit available, allowing braking of the rear wheel with the left hand
• Tested in the toughest conditions

• Approvals: HOMNN_EU

• Manifold routing optimally adapted to the production engine
• Silencer housing made of high-grade titanium
• Complies with current FIM noise regulations
• Complies with current AMA noise regulations
• Stainless steel header
• More usable speed range
• Better power delivery
• Improved handling overall due to finer dosing capacity on the throttle grip
• Sensitive response
• Rich sound
• Increased tightening torque
• Increased performance
• Factory Racing Team look

• Approvals: CCCUO_EU
• Factory Racing: USED BY FACTORY RACING
• Mapping: Mapping
• Material (PowerParts): Stainless steel

• Made from high grade titanium
• Uncompromising race look
• Permanently welded brackets
• Complies with current FIM noise regulations
• Substantial weight saving

• Approvals: CCCUO_EU
• Material (PowerParts): Titanium

• Silencer housing made of high-grade aluminum
• Carbon silencer cap
• Mounting also possible with original header
• Significantly more torque
• Substantial weight saving
• Noticeable performance enhancement

ATTENTION: When used on MX EU models from MY26 and MX US models from MY26 FACTORY EDITION / MY27 Standard, the air box and air filter must be reverted to MY25. The correct engine mapping must also be installed. Vehicles in this configuration no longer comply with the 109 dB FIM noise limit.

• Approvals: CCCUO_EU
• Colour: Grey
• Material (PowerParts): Carbon

• Silencer housing made of high-grade titanium
• Carbon silencer cap
• Mounting also possible with original header
• Significantly more torque
• Substantial weight saving
• Noticeable performance enhancement
• Blue anodised outer sleeve

ATTENTION: When used on MX EU models from MY26 and US models from MX MY26 FACTORY EDITION / MY27 Standard, the air box and air filter must be reverted to MY25. The correct engine mapping must also be installed. Vehicles in this configuration no longer comply with the 109 dB FIM noise limit.

• Approvals: CCCUO_EU
• Colour: Blue
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Carbon

• Manifold routing optimally adapted to the production engine
• Resonator chamber for optimum torque distribution and noise reduction
• Tangible performance boost over the entire engine speed range
• Highest quality workmanship

• Approvals: CCCUO_EU
• Mapping: Mapping
• Material (PowerParts): Stainless steel

• Stainless steel outer sleeve and interior
• Can only be fitted with a standard header
• Full sound
• Uncompromising race look
• Hard Enduro-compatible durability
• Complies with current FIM noise regulations
• Better power delivery
• Sensitive response

• Approvals: CCCUO_EU

• Coated neoprene ring
• Simply pulled over the grips

• Approvals: HOMNN_EU
• Colour: Orange

• Makes it easier to stand your motorcycle up
• Made of high-strength aluminum
• Essential under extreme off-road conditions
• Fastened to silencer support on the rear frame

• Approvals: HOMNN_EU
• Colour: Black

• Warm hands, no matter what the weather

• Approvals: HOMNN_EU

• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• Approvals: HOMNN_EU
• Colour: Grey
• Note: Closed end

• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• Approvals: HOMNN_EU
• Colour: Black
• Note: Closed end

• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• The different guide plates allow a variation of the throttle valve opening.

• Approvals: HOMNN_EU
• Colour: Grey
• Note: Closed end

• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• The different guide plates allow a variation of the throttle valve opening.

• Approvals: HOMNN_EU
• Colour: Grey
• Note: Open end

• Developed according to the requirements of our factory drivers
• Less stress when riding
• Objective: comfort AND safety
• Ergonomic contour adapted to the shape of the hand for maximum comfort
• Half waffle grip
• For a secure grip
• Three areas for the metal wire locking
• Version: medium

• Approvals: HOMNN_EU
• Colour: Grey
• Note: Closed end

• Developed according to the requirements of our factory drivers
• Less stress when riding
• Objective: comfort AND safety
• Ergonomic contour adapted to the shape of the hand for maximum comfort
• Half waffle grip
• For a secure grip
• Three areas for the metal wire locking
• Version: soft

• Approvals: HOMNN_EU
• Colour: Grey
• Note: Closed end

• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• The various cams can change the throttle valve opening speed

• Approvals: HOMNN_EU
• Colour: Orange
• Note: Closed end

• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• The different guide plates allow a variation of the throttle valve opening.

• Approvals: HOMNN_EU
• Colour: Orange
• Note: Open end

• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• Approvals: HOMNN_EU
• Colour: Black
• Note: Open end

• Makes it easier to stand your motorcycle up
• Specially developed for extreme conditions
• Strap made from high-strength nylon

• Approvals: HOMNN_EU
• Colour: Black
• Alignment: Front

• Makes it easier to stand your motorcycle up
• Essential under extreme off-road conditions
• Strap made from high-strength nylon

• Approvals: HOMNN_EU
• Alignment: Rear

• A motorcycle hand grip can be mounted on the handle (not included)

• The different guide plates allow a variation of the throttle valve opening.

• Approvals: HOMNN_EU

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic
• Excellent weather protection

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Ceramic white
• Material (PowerParts): Plastic

• Never again cold fingers!
• Mounting over handlebar and switches
• Better control during winter ride-outs

• Approvals: HOMNN_EU

• Made of robust plastic
• Fastening independent of fittings directly on the handlebars
• To convert the open, standard handguards to a closed version

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Made of robust plastic
• Fastening independent of fittings directly on the handlebars
• To convert the open, standard handguards to a closed version

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Made of robust plastic
• Fastening independent of fittings directly on the handlebars
• To convert the open, standard handguards to a closed version

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Attached directly at the levers with a special mounting

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design

• Attached directly at the levers with a special mounting.
• Only mountable with Brembo brake system

• Approvals: HOMNN_EU
• Colour: Orange
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Attached directly at the levers with a special mounting
• Only mountable with Brembo brake system

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design

• Attached directly at the levers with a special mounting.
• Only mountable with Brembo brake system

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Attached directly at the levers with a special mounting
• Only mountable with Brembo brake system

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design

• Approvals: HOMNN_EU
• Colour: White
• Material (PowerParts): Plastic

• Made of robust plastic
• To convert the open, standard handguards to a closed version

• Usable with handguards 7960297900028/30AB and 2650297900028/30/AB

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Extremely sturdy aluminum brackets
• Prevents broken levers
• Including all required assembly materials

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• CNC milled handlebar mount with damping rubber inserts
• Gentle on wrists and shoulder joints
• Damping of hard shocks
• Absorption of chassis and engine vibrations
• Additional handlebar damping in horizontal direction
• Optimum steering precision

• Approvals: CCCUO_EU
• Colour: Silver
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Approvals: CCCUO_EU
• Colour: Silver
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Height (PowerParts): 36

• When locked, the crossbar is solid (stiff)
• When unlocked, the crossbar is flexible

Dimensions: A = 112 mm, B = 811 mm, C = 88 mm

• Approvals: CCCUO_EU
• Diameter: 28 mm
• Factory Racing: USED BY FACTORY RACING

• The Twinwall, in the KTM orange design
• Two handlebars in one
• The exterior ensures maximum resistance to external damage (e.g. fall)
• Additionally hard anodised against corrosion
• The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls.
• Nylon inserts in the inner tube allow thinner walls
• Very good flex properties
• Comes with handlebar pad

• Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

• Approvals: CCCUO_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• The Twinwall, in the KTM orange design
• Two handlebars in one
• The exterior ensures maximum resistance to external damage (e.g. fall)
• Additionally hard anodised against corrosion
• The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls.
• Nylon inserts in the inner tube allow thinner walls
• Very good flex properties
• Comes with handlebar pad

• Dimensions: A = 104 mm, B = 811 mm, C = 74 mm

• Approvals: CCCUO_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Two handlebars in one
• The exterior ensures maximum resistance to external damage (e.g. fall)
• Additionally hard anodised against corrosion
• The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls.
• Nylon inserts in the inner tube allow thinner walls
• Very good flex properties
• Comes with handlebar pad

Renthal Twinwall 996

• Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

• Approvals: CCCUO_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Made of high-strength aluminum
• Tested in complex and specially-developed test cycles
• Position markings for easy adjustment

• Dimensions: A = 115 mm, B = 806 mm, C = 62 mm

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Enables power consumers such as grip heater or radiator fans to be installed on motocross or cross-country models as well

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU

• Plug & Play mounting
• Attachment to handlebar

• Approvals: CCCUO_EU

• Plug & Play mounting
• Waterproof switch
• Optimal protection against stone impact

Functional cover made of textile fabric to protect the wire from damage and soiling.

• Approvals: CCCUO_EU

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight with technical and ergonomic added value
• Adjustable grip width

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight with technical and ergonomic added value
• Ergonomically perfect shape (the result of years of racing experience)
• Adjustable grip width

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Weight: 0.055

• Elegant anodised surface
• Visual highlight with technical and ergonomic added value
• Flaps removed on ground contact
• Prevents broken levers

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Elegant anodised surface
• Visual highlight with technical and ergonomic added value
• Flaps removed on ground contact
• Prevents broken levers

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Including plastic insert
• Reduces the risk of a lever being broken

Suitable for all Brembo® and Formula brake and clutch assembles

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Prevents the hand grips from chafing in the event of a fall

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Already mandatory in many competitions
• Provides optimum protection

• Approvals: HOMNN_EU
• Colour: Orange

• Exceptionally robust
• Extremely light

• Approvals: CCCUO_EU
• Colour: Black
• Alignment: Left