Medium strength thread lock - contents, 50 ml.

• Temperature resistant from -55 to +200 °C 
• Fills gaps up to 0.25 mm
• Final strength achieved after 1 to 3 hours
  

Medium-strength thread lock. Suitable for all metal thread connections.

• Developed according to the requirements of our factory drivers
• Less stress when riding
• Objective: comfort AND safety
• Ergonomic contour adapted to the shape of the hand for maximum comfort
• Half waffle grip
• For a secure grip
• Three areas for the metal wire locking
• Version: medium

• Combines the durability of the KTM standard grips with the comfort of the soft KTM grips
• Harder orange material on the inside and on the grip ends for long durability
• Softer black material on the outside for increased comfort

• Combines the durability of the KTM standard grips with the comfort of the soft KTM grips
• Harder orange material on the inside and on the grip ends for long durability
• Softer black material on the outside for increased comfort

The oil filter kit contains all the filters, sieves, O-rings and seals you need for an oil change.

HeliCoil plus

Spark plug thread repair selection M10x1 / M12x1.25 / M14x1.25.

Individual pre-oiled air filter

This large-pore air filter cover acts as an additional protective layer, hence extending the filter service interval. Recommended in extremely dusty conditions.

Recommended in extremely wet conditions.

• Developed together with the vehicle
• Fork bleeding using finger pressure
• Specially developed for WP forks

ORGANIC BRAKE PADS

• Made from a special material mix with a high proportion of organic substances, therefore softer
• With ceramic underlayer for optimum thermal insulation
• Lower friction coefficient than sintered brake pads, so less aggressive braking feel
• Beneficial when particularly refined responsiveness is desired for ideal brake application

• Made from a special material mix with a high proportion of organic substances, therefore softer
• With ceramic underlayer for optimum thermal insulation
• Lower friction coefficient than sintered brake pads, so less aggressive braking feel
• Beneficial when particularly refined responsiveness is desired for ideal brake application

• 100% sintered metals
• Very high coefficient of friction for maximum and enduring braking power
• Low "fading" tendency when hot
• Very effective braking in the wet as well
• Very hard and therefore extremely long-lasting
• Particularly beneficial in extreme conditions (e.g. sand, gravel, etc.)

• Made from a special material mix with a high proportion of organic substances, therefore softer
• With ceramic underlayer for optimum thermal insulation
• Lower friction coefficient than sintered brake pads, so less aggressive braking feel
• Beneficial when particularly refined responsiveness is desired for ideal brake application

• 100% sintered metals
• Very high coefficient of friction for maximum and enduring braking power
• Low "fading" tendency when hot
• Very effective braking in the wet as well
• Very hard and therefore extremely long-lasting
• Particularly beneficial in extreme conditions (e.g. sand, gravel, etc.)

ORGANIC BRAKE PADS

• Made from a special material mix with a high proportion of organic substances, therefore softer
• With ceramic underlayer for optimum thermal insulation
• Lower friction coefficient than sintered brake pads, so less aggressive braking feel
• Beneficial when particularly refined responsiveness is desired for ideal brake application

• Anodized D.I.D DirtStar rim - an ideal compromise between rigidity and flexibility
• Anodized from the full milled hub - specially developed and coordinated to the properties of the D.I.D DirtStar rim
• Maximum weight saving compared to standard wheels
• Maximum gain in handling and, at the same time, stability in challenging offroad application
• 36 spoke design
• Anodized spoke nipple made from aluminum
• For axle diameter 20 mm

• Anodized D.I.D DirtStar rim - an ideal compromise between rigidity and flexibility
• Anodized from the full milled hub - specially developed and coordinated to the properties of the D.I.D DirtStar rim
• Maximum weight saving compared to standard wheels
• Maximum gain in handling and, at the same time, stability in challenging offroad application
• 36 spoke design
• Anodized spoke nipple made from aluminum
• For axle diameter 25 mm

• Convenient and easy to use
• Easy to store
• Waterproof packaging

• Contents are in accordance with DIN standard 13167-2014 for motorcyclists
• Note: It is mandatory to carry a first aid kit in many countries (such as Austria, Italy, Portugal and Spain).

• Increased performance along with minimized noise level
• Manufactured from highest grade materials
  With removable noise reduction insert.

The benefits:

• Increased performance along with minimized noise level
• Manufactured from highest grade materials

With removable noise reduction insert.
Can only be fitted in combination with original header.

• Extremely light: about 80% lighter than steel with the same load-bearing capacity
• Very stable: 4 times more resilient than aluminum
• Ultimate stiffness and strength
• Free from corrosion
• High continuous temperature resistance
• Low thermal expansion
• And, last but not least, a cool look
  Pimp your KTM with carbon components from KTM PowerParts - they save weight and look great.

• Manufactured from carbon
• Optimum protection against stone impacts
• For fork tube with a diameter of 48 mm

The closed, two-component plastic handguards developed by KTM feature a black center section that offers maximum strength for optimum protection. The colorful upper and lower parts are highly flexible and endure even the roughest of treatment without complaint. Available in two different heights.

• Enables secure attachment to the machine without scratching your handlebars or tank
• Made from durable ballistic nylon
• Load capacity of 280 kg
• Dimensions: 3,8 cm x 0,6 m
• 2 units

• Enables secure attachment to the machine without scratching your handlebars or tank
• Made from durable ballistic nylon
• Load capacity of 280 kg
• With handlebar loops
• With rubberized hooks on both belt ends
• 2 units

The following benefits are the mark of our lithium-ion batteries:

• 1 kg lighter than the standard battery 77311053000
• 1.6 kg lighter than the standard battery 58511053000
• Unbeatable cost/weight saving ratio
• Mountable in any position, as it does not contains acid
• Safe technology and long life

Technical data:

• 12 V maintenance-free LiFePo4-battery
• Capacity 1.2 Ah
• Recommended charging current - 2.5 amps
• Maximum charge current for fast charging - 12 amps
• Fast charge with high charging current (up to 90% in 6 min)
• Very low self-discharge (max. 5% per month)
• Balanced discharge/charge of all cells through balancer
• Contains no heavy metals

When mounting on 125 SX and SX-F models from 2016 onwards, the battery compartment 790.11.955.044 is also required.

• Can be mounted without additional mounting material
• Welded seams
• Robust and waterproof bag
• Waterproof roll closure
• Resistant waterproof coating

DO YOU KNOW that all KTM CNC parts are manufactured from highest quality aluminum and therefore not only look good, they also withstand the toughest treatment? With the anodized aluminum components in the original factory look from the PowerParts range, you can turn your KTM into something very special.

• Spring-mounted, 20° rotational movement possible towards front and rear
• More control and grip in the corners thanks to the maneuverability
• Large tread surface area of 60 mm
• Simpler and quicker weight shifting
• Simpler gear changing and braking
• Permanent contact between boot and foot pegs: extends the service life of your boots!

Indispensable in extreme conditions, this fan provides more air, ensuring better cooling and maximum power. It’s in your own hands: With the digital control unit, you can adjust the activation temperature to suit prevailing conditions and read the current temperature at any time. The freely selectable activation temperature lies between 65°C and 95°C. The deactivation temperature is adjusted automatically and always lies 1°C below the selected activation temperature. For the installation on EXC 4-stroke models till MY11 and on all EXC 2-stroke models the auxiliary wiring harness 777.11.979.000 is needed. From MY14 the Y-distributor wiring 777.11.979.010 is required for the installation on EXC 4-stroke models. Auxiliary wiring harness 777.11.979.000 for installation on  XC models.

• Manufactured from high-strength 7075-T6 aluminum, the strongest aluminum in the world
• Free from vibration - therefore the highest power transmission efficiency
• No small stones or dirt particles can become stuck under the chain thanks to angled recesses between the teeth
• Orange anodized with a permanent, organic and environmentally friendly pigment

• Manufactured from high-strength 7075-T6 aluminium - the world's strongest aluminium.
• Sprockets with different teeth number as stock are CCCUO_EU!

• Manufactured from high-strength 7075-T6 aluminum - the world's strongest aluminum

The orange rear sprocket is already a true classic that has established itself with really strong arguments and many benefits:

• Manufactured from high-strength 7075-T6 aluminium, the strongest aluminium in the world
• Free from vibration - therefore the highest power transmission efficiency
• No small stones or dirt particles can become stuck under the chain thanks to angled recesses between the teeth
• Orange anodised with a permanent, organic and environmentally friendly pigment

The orange rear sprocket is already a true classic that has established itself with really strong arguments and many benefits:

• Manufactured from high-strength 7075-T6 aluminium, the strongest aluminium in the world
• Free from vibration - therefore the highest power transmission efficiency
• No small stones or dirt particles can become stuck under the chain thanks to angled recesses between the teeth
• Orange anodised with a permanent, organic and environmentally friendly pigment

• Manufactured from high-strength 7075-T6 aluminum, the strongest aluminum in the world
• Free from vibration - therefore the highest power transmission efficiency
• No small stones or dirt particles can become stuck under the chain thanks to angled recesses between the teeth
• Orange anodized with a permanent, organic and environmentally friendly pigment

• Made from 4mm-thick, high-strength, robust aluminum
• Extremely hard-wearing and endurance-tested for the toughest offroad use
• Precisely fitting design - specially developed for KTM models
• Highest quality workmanship
• Quick and simple installation

• Made from 4mm-thick, high-strength, robust aluminum
• Extremely hard-wearing and endurance-tested for the toughest offroad use
• Precisely fitting design - specially developed for KTM models
• Highest quality workmanship
• Quick and simple installation

• Diameter 220 mm
• Manufactured from special high-grade stainless steel
• Full version for muddy track conditions
• Minimizes wear of the brake linings

• Diameter 310 mm
• Floating brake disc manufactured from special high-grade stainless steel
• Internal ring made from high-grade aluminum
• Larger diameter for added braking performance
• Minimal wear on brake linings
• Can only be used in conjunction with the 4-piston brake caliper 58413015644/04 or 6-piston brake caliper 59413015044/04

• The Z-ring or X-ring has 4 contact points in contrast to 2 contact points with the O-ring version
• This means higher flexibility and better running characteristics for the Z-ring or X-ring chain
• The spring effect of the Z-ring or X-ring guarantees consistent and permanent lubrication
• This means a significantly longer service life for the Z-ring or X-ring chain
• The Z-ring or X-ring provides a better seal against penetration by water and dirt

• CNC milled from high-strength solid aluminum
• Chrome-plated pad guide pins on the brake caliper
• The benefits:
  
  • Reduced brake pad canting, hence no uneven wear
  • Constant braking feel, irrespective of brake pad wear or temperature
  • No vibration from the brake

Fitting possible on SX/EXC models without adapter, with the original hand pump and brake hose.
Can only be fitted with a 17"or 16.5" front wheel. 310 mm brake disc 586.09.060.000 or 250.09.260.000 required.
In combination with brake disc 25009260000 (310 mm) no speedometer signal will be sent.

• Made of high-quality carbon
• Visual highlight
• Optimal protection against stone impact
• High stiffness and strength
• Optimal protection against stone impact

• Made of high-strength aluminum
• Clear pressure point across the entire temperature range
• More brake power
• Higher stiffness with the same weight

• Made of high-strength aluminum
• Clear pressure point across the entire temperature range
• More brake power
• Higher stiffness with the same weight

• Made of high-strength aluminum
• Perfect dosing capacity
• Requires significantly less manual force
• Larger piston than standard

• Radial hand brake cylinder with 16 mm piston
• Allows better leverage than conventional brake cylinders

• Outer ring made of stainless high-performance brake steel
• Larger diameter for added braking performance

• Floating
• Inner ring anodized
• Outer ring made of stainless high-performance brake steel
• Minimal wear on brake pads
• With Flame design for added braking performance

• Floating brake disc manufactured from special high-grade stainless steel
• With Flame design for added braking performance
• Minimal wear on brake linings

• No fading
• Outer ring made of stainless high-performance brake steel
• Minimal wear on brake pads
• Significantly longer lasting
• With Flame design for added braking performance

• No fading
• Outer ring made of stainless high-performance brake steel
• Minimal wear on brake pads
• Significantly longer lasting
• With Flame design for added braking performance

• Minimal wear on brake pads
• Significantly longer lasting
• Full version for muddy track conditions

• Floating
• Outer ring made of stainless high-performance brake steel
• Inner ring anodized
• Minimal wear on brake pads
• Larger diameter for added braking performance

• Can only be used in conjunction with 4 piston brake caliper 5841301564404 or 6 piston brake caliper 5941301504404
• In combination with 4 piston brake caliper 58413015644/04 no speedometer signal will be sent

• Floating
• Outer ring made of stainless high-performance brake steel
• Inner ring anodized
• Minimal wear on brake pads

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

• With return valve
• Anodized dust protection cap
• Quick and easy bleeding of the brake

• With return valve
• Anodized dust protection cap
• Quick and easy bleeding of the brake

• Made of high-strength aluminum
• Improved braking performance

• Made of high-strength aluminum
• Improved braking performance

• CNC milled from high-strength aluminum
• Lighter than series components
• Protects the brake disc in the event of a fall
• High stiffness and strength
• Protects the rear brake disc from stones and other solid obstacles

• CNC milled from high-strength aluminum
• Lighter than series components
• Protects the brake disc in the event of a fall
• High stiffness and strength
• Protects the rear brake disc from stones and other solid obstacles

• CNC milled from high-strength aluminum
• Lighter than series components
• Protects the brake disc in the event of a fall
• High stiffness and strength
• Protects the rear brake disc from stones and other solid obstacles

• Replaces the standard pins
• Quick and easy brake pad change even in difficult conditions

• Increases the volume of the rear master cylinder
• Additional cooling ribs minimize the heating of the brake fluid
• Eliminates “fading” almost completely

• Allows the rear wheel to be braked with the left hand
• Provides additional control in critical riding situations
• For use with the automatic clutch

• Protects the brake pedal from bending by branches

• For all 48 mm forks
• Made of high-quality carbon

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Visual highlight
• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Visual highlight
• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Greater flexibility and better running characteristics
• Constant and permanent lubrication
• Better sealing against water and dirt
• Significantly longer durability

• Greater flexibility and better running characteristics
• Constant and permanent lubrication
• Better sealing against water and dirt
• Significantly longer durability

• Elegant anodized surface
• Extremely light
• Made of high-strength aluminum
• Visual highlight
• Precisely ground to 0.002 mm, dead straight and impact-free chain track
• Free from vibration – therefore the highest power transmission efficiency
• Reduces the rotating masses

• Recommended for long journeys
• Significantly longer durability
• Teeth made of high-strength steel, for an extra long service life
• Extremely low-wear

• Teeth made of high-strength steel, for an extra long service life
• Aluminum center section, reduces unsprung masses
• Permanently joined together with high-strength rivets
• At least three times longer service life than other aluminum rear sprockets
• 50 % lighter than steel rear sprockets
• Longer service life of the entire drivetrain kit

• Teeth made of high-strength steel, for an extra long service life
• Aluminum center section, reduces unsprung masses
• Permanently joined together with high-strength rivets
• At least three times longer service life than other aluminum rear sprockets
• 50 % lighter than steel rear sprockets
• Longer service life of the entire drivetrain kit

• Teeth made of high-strength steel, for an extra long service life
• Aluminum center section, reduces unsprung masses
• Permanently joined together with high-strength rivets
• At least three times longer service life than other aluminum rear sprockets
• 50 % lighter than steel rear sprockets
• Longer service life of the entire drivetrain kit

• Prevents the chain from hitting the rear tyre
• Perfect chain guide, no branches drawn in between chain and engine housing

In orange Factory look.

• Visual highlight
• Race look

• Visual highlight
• Race look
• Factory Racing Team look
• With exchangeable chain track surface, therefore extremely durable
• Specially designed for the challenges of off-road use

• Made of high-strength aluminum

• Protects the chain guide bracket against damage

• Developed together with the vehicle
• Specially developed for WP forks
• Fork bleeding using finger pressure

• Quick preload adjustment
• Use of the entire thread length on the shock absorber
• Very simple to use
• Low weight
• dust-resistant
• Mechanical drive mechanism

• CNC milled from high-strength aluminum
• Elegant anodized surface
• Visual highlight

• CNC milled from high-strength aluminum
• Elegant anodized surface
• Easy to mount
• Visual highlight
• Suitable for the left and right side

• CNC milled from high-strength aluminum
• Elegant anodized surface
• Visual highlight

• CNC milled from high-strength aluminum
• Elegant anodized surface

• CNC milled from high-strength aluminum
• Elegant anodized surface
• Visual highlight
• Includes drilling for safety wire

• For extremely muddy conditions
• Protects the radiator from mud, dirt and sand
• Protection against rapid overheating of the engine in muddy conditions

• Improved torque curve combined with very rideable peak performance
• More sensitive throttle response and resulting improved traction
• Durability suitable for extreme enduro use
• Made from titanium - that means: ultra-light
• Welded on brackets
• Reinforced titanium end cap (factory team standard)
• Pleasant deep sound
• Tuned for compliance with the latest applicable noise regulations

With removable noise reduction insert.
Can only be fitted in combination with original header.

• Extremely light
• Extremely durable
• Low thermal expansion
• High long-term temperature stability
• Maximum protection against falls, flying stones, branches, etc.
• Visual highlight
• Protects against heat and unwanted contact
• High stiffness and strength

• For extremely muddy conditions

• Move along with weight shift
• Permanent contact between boot and footpeg
• Extends the service life of your boots
• Enlarged tread area
• More control
• More curve pressure
• Easier and faster weight shifting
• Easier shifting and braking

Spring-mounted, 20-degree rotational movement possible towards front and rear

• Coated neoprene ring
• Simply pulled over the grips

• Grip made of high-strength aluminum
• Essential for extreme off-road use
• Makes it easier to stand your motorcycle up
• Attached to the silencer support on the subframe

• Warm hands, no matter what the weather

• Developed according to the requirements of our factory drivers
• Less stress when riding
• Objective: comfort AND safety
• Ergonomic contour adapted to the shape of the hand for maximum comfort
• Half waffle grip
• For a secure grip
• Three areas for the metal wire locking
• Version: soft

• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• For a secure grip
• Maximum grip on the hand grip even in extremely muddy conditions

• Specially developed for extreme conditions
• Strap made from high-strength nylon
• Makes it easier to stand your motorcycle up

• High-strength nylon strap
• Indispensable for use on extreme terrain
• Makes it easy to get your bike upright
• Attaches to rear frame

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Improved optics

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Improved optics

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Improved optics

• Excellent weather protection
• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Improved optics

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Excellent weather protection
• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Excellent weather protection
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Excellent weather protection
• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Extremely light
• Uncompromising race look
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions

• Extremely light
• Uncompromising race look
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions

• Black mid-section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible, enduring even the roughest of treatment
• Attached directly at the levers with a special mounting.

• Black mid-section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible, enduring even the roughest of treatment
• Attached directly at the levers with a special mounting.

• Black mid-section = maximum strength for optimum protection
• Orange top and bottom parts = highly flexible, enduring even the roughest of treatment

• Never again cold fingers!
• Mounting over handlebar and switches
• Better control during winter ride-outs

• CNC milled handlebar mount with damping rubber inserts
• Gentle on wrists and shoulder joints
• Damping of hard shocks
• Absorption of chassis and engine vibrations
• Additional handlebar damping in horizontal direction
• Optimum steering precision
• Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment

• Handlebar height adjustable to 2 positions

• Made of high-strength aluminum
• Tested in complex and specially-developed test cycles
• Position markings for easy adjustment

• Dimensions: A = 115 mm, B = 806 mm, C = 62 mm

• The Twinwall, in the KTM orange design
• Two handlebars in one
• The exterior ensures maximum resistance to external damage (e.g. fall)
• Additionally hard anodized against corrosion
• The interior, made of a special alloy, is also hard anodized to protect it from damage by the handlebar controls.
• Nylon inserts in the inner tube allow thinner walls
• Very good flex properties
• Comes with handlebar pad

Dimensions: A = 79 mm, B = 811 mm, C = 74 mm

• The Twinwall, in the KTM orange design
• Two handlebars in one
• The exterior ensures maximum resistance to external damage (e.g. fall)
• Additionally hard anodized against corrosion
• The interior, made of a special alloy, is also hard anodized to protect it from damage by the handlebar controls.
• Nylon inserts in the inner tube allow thinner walls
• Very good flex properties
• Comes with handlebar pad

• Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

• Enables power consumers such as grip heater or radiator fans to be installed on SX or XC as well

• Know exactly when the next service is due

• Higher cold current value (CCA) for improved cold start characteristics
• Unbeatable cost/weight saving ratio
• Mountable in any position, as it does not contains acid
• Safe technology and long life

• 1 kg lighter than lead-acid battery 77311053000
• 1.6 kg lighter than lead-acid battery 58511053000

Technical data:

• 12 V maintenance-free LiFePo4-battery
• Capacity 2.0 Ah
• Recommended charging current - 2.5 amps
• Maximum charge current for fast charging - 10 amps
• Fast charge with high charging current (up to 90% in 10 min)
• Very low self-discharge (max. 5% per month)
• Balanced discharge/charge of all cells through balancer
• Contains no heavy metals
• When mounting on 125 SX and SX-F models from 2016 onwards, the battery compartment 79011955044 is also required.

• Manufactured from high-strength aluminum, forged and then CNC-machined
• This extensive production process guarantees a long service life, maximum flexibility and a precise fit
• Ergonomically perfected shape (the result of years of racing experience)
• Predefined breaking point
• Orange anodized

• CNC milled from high-strength aluminum
• Elegant anodized surface
• Visual highlight with technical and ergonomic added value
• Ergonomically perfect shape (the result of years of racing experience)
• The brake or clutch fitting rotates in the event of a fall
• Adjustable grip width

• Elegant anodized surface
• Visual highlight with technical and ergonomic added value
• The brake or clutch fitting rotates in the event of a fall

• CNC milled from high-strength aluminum
• Elegant anodized surface
• Visual highlight
• Including plastic insert
• The brake or clutch fitting rotates in the event of a fall
• Reduces the risk of a lever being broken

Suitable for all Brembo® and Formula brake and clutch assembles

• CNC milled from high-strength aluminum
• Elegant anodized surface
• Visual highlight
• Prevents the hand grips from chafing in the event of a fall

• Already mandatory in many competitions
• Provides optimum protection
• Visual highlight

• Already mandatory in many competitions
• Provides optimum protection
• Visual highlight

• Exceptionally robust
• Extremely light

• Protects your expensive smartphone from rain, dust or mud
• Touchscreen remains fully functional
• Optimal solution for quickly and securely attaching the smartphone to the vehicle
• Handlebar pad and smartphone holder in one
• Smartphone cover with velcro fastener attached to the handlebar pad
• Smartphone can be easily removed with its cover

• For Smartphones up to 160 x 80 mm
• Comes with two separate protective strips in case the sleeve is not used
• Can also be fitted in combination with the PHDS-handlebar support
• Smartphone not included!

• Prevents snapping of throttle cable wire
• Simple to fit
• Made of aluminum

• Top performance/price ratio
• Gain in stability at the front wheel
• Fully adjustable
• Well thought-out mounting of the damper enables individual handlebar adjustment

• Developed according to the requirements of our factory drivers
• Gain in stability at the front wheel
• High-end steering damper
• Maximum control on fast tracks
• Fully adjustable
• Well thought-out mounting of the damper enables individual handlebar adjustment
• Reduced weight
• Sensitive response behavior
• High speed DCC

• Optimum 25 click setting range
• Proven success with the KTM Works Rally Team

• Resistant waterproof coating
• Waterproof roll closure
• For waterproof storage of documents, maps, cellphones, navigation devices etc.

• Can be mounted without additional mounting material
• Welded seams
• Robust and waterproof bag
• Waterproof roll closure
• Resistant waterproof coating

• For waterproof storage of documents, maps, cellphones, navigation devices etc.

• Suitable for all Garmin GPS devices
• Suitable for all TomTom GPS devices
• Suitable for the Touratech iBracket
• Mounting on the standard handlebar clamps

• Universally applicable for mounting the GPS bracket

• Universal and inconspicuous bracket for your smartphone
• Optimal solution for quickly and securely attaching the smartphone to the vehicle

• Can be clamped on the handlebar (including different adaptor)
• The arm can be rotated in any position for the perfect position for your smartphone

• Optimal solution for quickly and securely attaching the smartphone to the vehicle
• Smartphone can be easily removed with its cover

• Protects your expensive smartphone

• Optimal solution for quickly and securely attaching the smartphone to the vehicle
• Smartphone can be easily removed with its cover

• Protects your expensive smartphone

• Optimal solution for quickly and securely attaching the smartphone to the vehicle
• Smartphone can be easily removed with its cover

• Protects your expensive smartphone

• Optimal solution for quickly and securely attaching the smartphone to the vehicle
• Smartphone can be easily removed with its cover

• Protects your expensive smartphone

• Optimal solution for quickly and securely attaching the smartphone to the vehicle
• Smartphone can be easily removed with its cover

• Protects your expensive smartphone

• Optimal solution for quickly and securely attaching the smartphone to the vehicle
• Smartphone can be easily removed with its cover

• Protects your expensive smartphone

• Optimal solution for quickly and securely attaching the smartphone to the vehicle
• Smartphone can be easily removed with its cover

• Protects your expensive smartphone

• Optimal solution for quickly and securely attaching the smartphone to the vehicle
• Smartphone can be easily removed with its cover

• Protects your expensive smartphone

• Optimal solution for quickly and securely attaching the smartphone to the vehicle
• Smartphone can be easily removed with its cover

• Protects your expensive smartphone

• Optimal solution for quickly and securely attaching the smartphone to the vehicle
• Smartphone can be easily removed with its cover

• Protects your expensive smartphone

• Optimal solution for quickly and securely attaching the smartphone to the vehicle
• Smartphone can be easily removed with its cover

• Protects your expensive smartphone

• Optimal solution for quickly and securely attaching the smartphone to the vehicle
• Smartphone can be easily removed with its cover

• Protects your expensive smartphone

• Optimal solution for quickly and securely attaching the smartphone to the vehicle
• Smartphone can be easily removed with its cover

• Protects your expensive smartphone