This large-pore air filter cover acts as an additional protective layer, hence extending the filter service interval. Recommended in extremely dusty conditions.

Recommended in extremely wet conditions.

• Made from a special material mix with a high proportion of organic substances, therefore softer
• With ceramic underlayer for optimum thermal insulation
• Lower friction coefficient than sintered brake pads, so less aggressive braking feel
• Beneficial when particularly refined responsiveness is desired for ideal brake application

• 100% sintered metals
• Very high coefficient of friction for maximum and enduring braking power
• Low "fading" tendency when hot
• Very effective braking in the wet as well
• Very hard and therefore extremely long-lasting
• Particularly beneficial in extreme conditions (e.g. sand, gravel, etc.)

• Made from a special material mix with a high proportion of organic substances, therefore softer
• With ceramic underlayer for optimum thermal insulation
• Lower friction coefficient than sintered brake pads, so less aggressive braking feel
• Beneficial when particularly refined responsiveness is desired for ideal brake application

• 100% sintered metals
• Very high coefficient of friction for maximum and enduring braking power
• Low "fading" tendency when hot
• Very effective braking in the wet as well
• Very hard and therefore extremely long-lasting
• Particularly beneficial in extreme conditions (e.g. sand, gravel, etc.)

ORGANIC BRAKE PADS

• Made from a special material mix with a high proportion of organic substances, therefore softer
• With ceramic underlayer for optimum thermal insulation
• Lower friction coefficient than sintered brake pads, so less aggressive braking feel
• Beneficial when particularly refined responsiveness is desired for ideal brake application

• Extremely light: about 80% lighter than steel with the same load-bearing capacity
• Very stable: 4 times more resilient than aluminum
• Ultimate stiffness and strength
• Free from corrosion
• High continuous temperature resistance
• Low thermal expansion
• And, last but not least, a cool look
  Pimp your KTM with carbon components from KTM PowerParts - they save weight and look great.

• Manufactured from carbon
• Optimum protection against stone impacts
• For fork tube with a diameter of 48 mm

The closed, two-component plastic handguards developed by KTM feature a black center section that offers maximum strength for optimum protection. The colorful upper and lower parts are highly flexible and endure even the roughest of treatment without complaint. Available in two different heights.

• Black center section = maximum strength for optimum protection
• Coloured upper and lower parts = highly flexible for enduring the roughest of treatment
• The choice is yours: attached directly to the handlebar with a plastic bracket or directly to the lever mounting with a special adaptor.
• Cannot be fitted with Twinwall handlebar.

Attached directly at the levers with a special mounting.

• Enables secure attachment to the machine without scratching your handlebars or tank
• Made from durable ballistic nylon
• Load capacity of 280 kg
• Dimensions: 3,8 cm x 0,6 m
• 2 units

• Enables secure attachment to the machine without scratching your handlebars or tank
• Made from durable ballistic nylon
• Load capacity of 280 kg
• With handlebar loops
• With rubberized hooks on both belt ends
• 2 units

The following benefits are the mark of our lithium-ion batteries:

• 1 kg lighter than the standard battery 77311053000
• 1.6 kg lighter than the standard battery 58511053000
• Unbeatable cost/weight saving ratio
• Mountable in any position, as it does not contains acid
• Safe technology and long life

Technical data:

• 12 V maintenance-free LiFePo4-battery
• Capacity 1.2 Ah
• Recommended charging current - 2.5 amps
• Maximum charge current for fast charging - 12 amps
• Fast charge with high charging current (up to 90% in 6 min)
• Very low self-discharge (max. 5% per month)
• Balanced discharge/charge of all cells through balancer
• Contains no heavy metals

When mounting on 125 SX and SX-F models from 2016 onwards, the battery compartment 790.11.955.044 is also required.

DO YOU KNOW that all KTM CNC parts are manufactured from highest quality aluminum and therefore not only look good, they also withstand the toughest treatment? With the anodized aluminum components in the original factory look from the PowerParts range, you can turn your KTM into something very special.

• Spring-mounted, 20° rotational movement possible towards front and rear
• More control and grip in the corners thanks to the maneuverability
• Large tread surface area of 60 mm
• Simpler and quicker weight shifting
• Simpler gear changing and braking
• Permanent contact between boot and foot pegs: extends the service life of your boots!

Indispensable in extreme conditions, this fan provides more air, ensuring better cooling and maximum power. It’s in your own hands: With the digital control unit, you can adjust the activation temperature to suit prevailing conditions and read the current temperature at any time. The freely selectable activation temperature lies between 65°C and 95°C. The deactivation temperature is adjusted automatically and always lies 1°C below the selected activation temperature. For the installation on EXC 4-stroke models till MY11 and on all EXC 2-stroke models the auxiliary wiring harness 777.11.979.000 is needed. From MY14 the Y-distributor wiring 777.11.979.010 is required for the installation on EXC 4-stroke models. Auxiliary wiring harness 777.11.979.000 for installation on  XC models.

• Manufactured from high-strength 7075-T6 aluminum, the strongest aluminum in the world
• Free from vibration - therefore the highest power transmission efficiency
• No small stones or dirt particles can become stuck under the chain thanks to angled recesses between the teeth
• Orange anodized with a permanent, organic and environmentally friendly pigment

The orange rear sprocket is already a true classic that has established itself with really strong arguments and many benefits:

• Manufactured from high-strength 7075-T6 aluminium, the strongest aluminium in the world
• Free from vibration - therefore the highest power transmission efficiency
• No small stones or dirt particles can become stuck under the chain thanks to angled recesses between the teeth
• Orange anodised with a permanent, organic and environmentally friendly pigment

The orange rear sprocket is already a true classic that has established itself with really strong arguments and many benefits:

• Manufactured from high-strength 7075-T6 aluminium, the strongest aluminium in the world
• Free from vibration - therefore the highest power transmission efficiency
• No small stones or dirt particles can become stuck under the chain thanks to angled recesses between the teeth
• Orange anodised with a permanent, organic and environmentally friendly pigment

The orange rear sprocket is already a true classic that has established itself with really strong arguments and many benefits:

• Manufactured from high-strength 7075-T6 aluminium, the strongest aluminium in the world
• Free from vibration - therefore the highest power transmission efficiency
• No small stones or dirt particles can become stuck under the chain thanks to angled recesses between the teeth
• Orange anodised with a permanent, organic and environmentally friendly pigment

• Manufactured from high-strength 7075-T6 aluminum, the strongest aluminum in the world
• Free from vibration - therefore the highest power transmission efficiency
• No small stones or dirt particles can become stuck under the chain thanks to angled recesses between the teeth
• Orange anodized with a permanent, organic and environmentally friendly pigment

• Made from polyester, with special rubberized back
• Gas and oil resistant
• In special KTM design
• Size: 100 x 170 cm

• New, even more robust, rear fastening clamp
• Made from 4mm-thick, high-strength, robust aluminum
• Side parts welded from inside and out
• Extremely hard-wearing and endurance-tested for the toughest offroad use
• Precisely fitting design - specially developed for KTM models
• Highest quality workmanship
• Quick and simple installation

• New, even more robust, rear fastening clamp
• Made from 4mm-thick, high-strength, robust aluminum
• Extremely hard-wearing and endurance-tested for the toughest offroad use
• Precisely fitting design - specially developed for KTM models
• Highest quality workmanship
• Quick and simple installation

ATTENTION: Brake line guide 76504042000 is required for correct mounting onto 125 SX, 250/350/450 SX-F for models made in the year 2016 and after.

• Ratchet (with locking device), lever, two extensions and socket wrench
• Hexagon sockets from 4 to 14
• Allen keys from 3 to 8
• Phillips, slotted and Torx bits

• Ratchet (with locking device), lever, two extensions and socket wrench
• Hexagon sockets from 6 to 24
• Allen keys from 3 to 10
• Phillips and slotted bits
• Torx bits from 15 to 55

• Diameter 220 mm
• Manufactured from special high-grade stainless steel
• Full version for muddy track conditions
• Minimizes wear of the brake linings

• Diameter 310 mm
• Floating brake disc manufactured from special high-grade stainless steel
• Internal ring made from high-grade aluminum
• Larger diameter for added braking performance
• Minimal wear on brake linings
• Can only be used in conjunction with the 4-piston brake caliper 58413015644/04 or 6-piston brake caliper 59413015044/04

• The Z-ring or X-ring has 4 contact points in contrast to 2 contact points with the O-ring version
• This means higher flexibility and better running characteristics for the Z-ring or X-ring chain
• The spring effect of the Z-ring or X-ring guarantees consistent and permanent lubrication
• This means a significantly longer service life for the Z-ring or X-ring chain
• The Z-ring or X-ring provides a better seal against penetration by water and dirt

• CNC milled from high-strength solid aluminum
• Chrome-plated pad guide pins on the brake caliper
• The benefits:
  
  • Reduced brake pad canting, hence no uneven wear
  • Constant braking feel, irrespective of brake pad wear or temperature
  • No vibration from the brake

Fitting possible on SX/EXC models without adapter, with the original hand pump and brake hose.
Can only be fitted with a 17"or 16.5" front wheel. 310 mm brake disc 586.09.060.000 or 250.09.260.000 required.
In combination with brake disc 25009260000 (310 mm) no speedometer signal will be sent.

• Manufactured from carbon
• Optimum protection against stone impacts
• Can be installed on brake caliper supports 79613975044, 7771397501030, 7771397511030, 78113975044, 78113975144, 78113975244, 78913975044 or 78913975144

• Floating brake disc manufactured from special high-grade stainless steel
• With Flame design for added braking performance
• Minimal wear on brake linings

• Floating brake disc manufactured from special high-grade stainless steel
• Internal ring made from high-grade aluminum
• With Wave design for added braking performance
• Minimal wear on brake pads
• Can only be used in conjunction with 4 piston brake caliper 5841301564404 or 6 piston brake caliper 5941301504404
• In combination with 4 piston brake caliper 58413015644/04 no speedometer signal will be sent

• Floating brake disc manufactured from special high-grade stainless steel
• Internal ring made from special high-grade stainless steel
• Minimal wear on brake linings

• Increases the volume of the foot brake cylinder
• The surface structure reduces the heat-up of the brake fluid
• Helps to eliminate dreaded "fading"
• Space requirements: Total height including cover approximately 26,5 mm

• Made of carbon
• Optimum protection against roost
• Made to fit all 48 mm forks

• The Z-ring or X-ring has 4 contact points in contrast to 2 contact points with the O-ring version
• This means higher flexibility and better running characteristics for the Z-ring or X-ring chain
• The spring effect of the Z-ring or X-ring guarantees consistent and permanent lubrication
• This means a significantly longer service life for the Z-ring or X-ring chain
• The Z-ring or X-ring provides a better seal against penetration by water and dirt

• higher flexibility and better running characteristics
• consistent and permanent lubrication
• better seal against water and dirt
• significantly longer service life

• Manufactured from high-strength 7075-T6 aluminum, the strongest aluminum in the world
• Originally developed for the aerospace industry and then adopted by the best rear sprocket manufacturer
• The chain runs smoothly, straigt as a die and true, because it`s ground level to an accuracy of 0.002mm
• Free from vibration - therefore the highest power transmission efficiency
• Orange anodized with a permanent, organic and environmentally friendly pigment
• Sprockets with different teeth number as stock are CCCUO_EU!

• For longer trips, we recommend this extremely low-wear, QStE 460 steel sprocket.
• Sprockets with different teeth number as stock are CCCUO_EU!

• High-strength alloy steel teeth for extra long life
• Aluminum center section reduces the unsprung mass
• Permanently joined together with high-tensile rivets
• At least three times longer service life than any other aluminum rear sprockets
• 50% lighter than conventional steel sprockets

Further advantages: Longer service life of the entire drive train kit

• High-strength alloy steel teeth for extra long life
• Aluminum center section reduces the unsprung mass
• Permanently joined together with high-tensile rivets
• At least three times longer service life than any other aluminum rear sprockets
• 50% lighter than conventional steel sprockets

Further advantages: Longer service life of the entire drive train kit

Manufactured exclusively for KTM by Supersprox. This product is protected by the following patents in the EU and the US. EU Patent # EP1573234. US Patent # 7.481.729. Patent holder Supersprox a.s.

• High-strength alloy steel teeth for extra long life
• Aluminum center section reduces the unsprung mass
• Permanently joined together with high-tensile rivets
• At least three times longer service life than any other aluminum rear sprockets
• 50% lighter than conventional steel sprockets

Further advantages: Longer service life of the entire drive train kit

• CNC-machined from Teflon
• With replaceable chain running surface, hence extremely durable
• Specially designed for the challenges of offroad use

• Manufactured from high-strength aluminum
• Protects the chain guide bracket from major damage
• Cannot be used in combination with the T.M. Designworks chain guide

Indispensable in extreme conditions, this fan ensures more air, better cooling and maximum performance. It's in your own hands: The digital control allows you to adjust the switch-on temperature to the present conditions and to read off the current temperature at any time. The freely selectable switch-on temperature is between 65 °C (149 °F) and 95 °C (203 °F).The switch-off temperature is adjusted automatically and is always 1 °C (34 °F) below the selected switch-on temperature. Auxiliary wiring harness 777.11.979.000 is required for installation on EXC 4-stroke models (up to and including model year 2011) and on all EXC 2-stroke models. As of model year 2014, Y-distributor 777.11.979.010 is required for installation on EXC 4-stroke models. Auxiliary wiring harness 777.11.979.000 is required for installation on XC models.

• Specially developed for Enduro application
• Made from high-grade aluminum
• With standard combustion chamber.

• Specially developed for extreme conditions
• Manufactured in a purpose developed alloy
• Enhanced performance from the engine due to the excellent conductivity of the material used with unchanged combustion chamber
• Reduces unwanted detonations in the cylinder, that in turn has a positive effect on the service life as well as on the performance of the engine

Akrapovi? Silencer - that means years of racing experience, perfect material selection and sports design.

The benefits:

• Minimum weight
• Maximum top-end performance
• Perfectly distributed torque curve
• Lowest noise level of any 2-stroke silencer
• Long service life

• Made from high quality, extra strong and durable sheet steel
• Nickel-plated surface
• Wide, even rev band
• High rev speed
• More traction and better control under full throttle
• Including O-rings
• Recommended in combination with an FMF silencer for a perfectly matched full system with optimum performance

Ingenious: Foot pegs that move with you when you shift your weight. Ideal for Motocross, Enduro and Supermoto.

The benefits:

• Spring-mounted, 20-degree rotational movement possible towards front and rear
• More control and grip in the corners thanks to the maneuverability
• Large tread surface of 60 mm
• Simpler and quicker weight shifting
• Simpler gear changing and braking
• Permanent contact between boot and foot peg: extends the service life of your boots!

• High-strength aluminum grip
• Indispensable for use on extreme terrain
• Makes it easy to get your bike upright
• Attaches to silencer bracket on rear frame
  

• Ergonomic; contour matched to the shape of the hand for maximum comfort
• Small "half waffle" ribs on the rear for secure grip
• Made from two materials with different grades of hardness
• Three areas for the metal safety wire
• Grip hardness: medium

• Ergonomic; contour matched to the shape of the hand for maximum comfort
• Small "half waffle" ribs on the rear for secure grip
• Made from two materials with different grades of hardness
• Three areas for the metal safety wire
• Grip hardness: soft

• Harder orange material on the inside and at the grip ends for a long service life
• Softer black material on the outside, where the hand lies on the grip, for increased comfort
• With open grip ends for closed handguards or bar ends

• Harder orange material on the inside and at the grip ends for a long service life
• Softer black material on the outside, where the hand lies on the grip, for increased comfort

• Grip replacement made easy
• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• High-strength nylon strap
• Indispensable for use on extreme terrain
• Attaches to fork tube

• High-strength nylon strap
• Indispensable for use on extreme terrain
• Makes it easy to get your bike upright
• Attaches to rear frame

• Black center section = maximum strength for optimum protection
• Coloured upper and lower parts = highly flexible for enduring the roughest of treatment
• The choice is yours: attached directly to the handlebar with a plastic bracket or directly to the lever mounting with a special adaptor.
• Cannot be fitted with Twinwall handlebar.

Attached directly at the levers with a special mounting.

This handguard set is not just visually impressive. Thanks to the special mix of materials, the handguard protects your hands and controls from damage without immediately breaking up. They also give you outstanding weather protection.

This handguard set is not just visually impressive. Thanks to the special mix of materials, the handguard protects your hands and controls from damage without immediately breaking up. They also give you outstanding weather protection.

This handguard set is not just visually impressive. Thanks to the special mix of materials, the handguard protects your hands and controls from damage without immediately breaking up. They also give you outstanding weather protection.

This handguard set has been specially developed for your motorcycle and is an essential accessory for heavy-duty offroad and Supermoto sessions. The broad, generous proportions, combined with the robust aluminum external frame ensure good mobility together with maximum protection in the event of a collision, stones thrown up from the road, branches etc.

• 78002079100EB is mounted standard on the 790 Adventure R
  

• Black center section = maximum strength for optimum protection
• Coloured upper and lower parts = highly flexible for enduring the roughest of treatment
• The choice is yours: attached directly to the handlebar with a plastic bracket or directly to the lever mounting with a special adaptor.
• Cannot be fitted with Twinwall handlebar.

Attached directly at the levers with a special mounting.

• Black center section = maximum strength for optimum protection
• Coloured upper and lower parts = highly flexible for enduring the roughest of treatment
• The choice is yours: attached directly to the handlebar with a plastic bracket or directly to the lever mounting with a special adaptor
• Cannot be fitted with Twinwall handlebar

Attached directly at the levers with a special mounting.

• Black mid-section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible, enduring even the roughest of treatment

• Black mid-section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible, enduring even the roughest of treatment

• Black center section = maximum strength for optimum protection
• Coloured upper and lower parts = highly flexible for enduring the roughest of treatment
• The choice is yours: attached directly to the handlebar with a plastic bracket or directly to the lever mounting with a special adaptor.
• Cannot be fitted with Twinwall handlebar.

Attached directly at the levers with a special mounting.

• Black center section = maximum strength for optimum protection
• Coloured upper and lower parts = highly flexible for enduring the roughest of treatment
• The choice is yours: attached directly to the handlebar with a plastic bracket or directly to the lever mounting with a special adaptor.
• Cannot be fitted with Twinwall handlebar.

Attached directly at the levers with a special mounting.

• Never again cold fingers!
• Mounting over handlebar and switches
• Better control during winter ride-outs

• Made of sturdy plastic
• Converts the originally open handguards into a closed version
• Compatible also with handguards 79602979000EB/28/30/AB and 72102979000EB/28/30

• Made of high-strength aluminum
• Converts the originally open handguards into a closed version
• Mounting independed to the lever mounting, directly to the handlebar
• Compatible also with handguards 79602182044 EB / 28 / 30

• Made of sturdy plastic
• Converts the originally open handguards into a closed version
• Mounting independed to the lever mounting, directly to the handlebar
• Compatible also with handguards 79602979000EB/28/30/AB and 72102979000EB/28/30

• Made of sturdy plastic
• Comes in a set incl. our well approved hand guards 7960218204430EB
• Mounting independent to the lever mounting, directly to the handlebar
  

• Made of sturdy plastic
• Comes in a set incl. our well approved hand guards 7960218204428
• Mounting independent to the lever mounting, directly to the handlebar
  

• Made of sturdy plastic
• Comes in a set incl. our well approved hand guards 7960218204430
• Mounting independent to the lever mounting, directly to the handlebar
  

• Made of sturdy plastic
• Comes in a set incl. our well approved hand guards 7960218204428
• Mounting independent to the lever mounting, directly to the handlebar
  

• Cushioning of heavy knocks
• Absorption of vibration from chassis and engine
• Additional handlebar damping in horizontal direction
• Optimum steering precision
• Handlebar height adjustable to 2 positions
• Further damping elements available in three degrees of hardness (soft, medium, hard) for individual tuning

• All KTM handlebars are made from EN AW 7010 T6 aluminum
• 28.5 mm diameter in the clamping area
• 22.15 mm diameter in the lever area
• Position markings for simple setting
• Dimensions: A = 115 mm, B = 806 mm, C = 62 mm

Dimensions: A = 79 mm, B = 811 mm, C = 74 mm

Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

We recommend using this additional wiring harness for all power consumers. Furthermore you have with the option of installing power consumers such as grip heating or a fan on your SX or XC with this wiring harness. Warning: The power consumer is now connected directly to the battery. If it is not turned off, the battery is therefore also drained when the engine is switched off. Optionally available: Y-distributor 777.11.979.010 or 777.11.979.044.

• Manufactured from high-strength aluminum, forged and then CNC-machined
• This extensive production process guarantees a long service life, maximum flexibility and a precise fit
• Ergonomically perfected shape (the result of years of racing experience)
• Predefined breaking point
• Orange anodized

• Manufactured from high-strength aluminum, forged and then CNC-machined
• This extensive production process guarantees a long service life, maximum flexibility and a precise fit
• Ergonomically perfected shape (the result of years of racing experience)
• Predefined breaking point
• Orange anodized

• Manufactured from high-strength aluminum, forged and then CNC-machined
• This extensive production process guarantees a long service life, maximum flexibility and a precise fit
• Ergonomically perfected shape (the result of years of racing experience)
• Predefined breaking point
• Orange anodized

• Including plastic insert
• The brake or clutch armature rotates in case of a fall
• Reduces the risk of a lever being broken
• Suitable for all Brembo® and Formula brake and clutch assembles

Provides optimum protection. With the integrated card holder you always have the time in view. A small extra pocket allows you to stow small items. Can also be fitted in combination with the PHDS-handlebar support.

00050000929 handle bar support kit required for use on MY16 and on XC from MY16.

• Extremely low weight
• Sensitive feedback behavior
• High speed setting
• Optimum 25 click setting range

Proven success with the KTM Works Rally Team. Fits all SX and EXC models.

Medium-strength thread lock. Suitable for all metal thread connections.

Medium strength thread lock - contents, 50 ml.

• Temperature resistant from -55 to +200 °C 
• Fills gaps up to 0.25 mm
• Final strength achieved after 1 to 3 hours
  

• Waterproof resistant coating
• Waterproof roll closure

• Suitable for all KTM GPS holders
• Size: 170 x 130 x 35 mm

Only for use on original handlebar mounting.

• Universal and discreet mounting solution for your smartphone
• Counterpart for the smartphone cases.
• The smartphone can be easily mounted on the motorcycle by turning it 90°.
• Can be clamped on the handlebar (including different adaptor)
• The arm can be rotated in any position for the perfect position for your smartphone.

• Made from neoprene
• Ideal protection for sealing the fork
• For use with the closed fork protector
• For fork tube with a diameter of 48 mm

• Made from neoprene
• Ideal protection for sealing the fork
• For use with the open fork protector
• For fork tube with a diameter of 48 mm

ATTENTION: Brake line guide 76504042000 is required for correct mounting onto 125 SX, 250/350/450 SX-F for models made in the year 2016 and after.

• Prevents damage to the engine case in the event of the chain breaking
• No pulling-in of stones between chain and engine case (material-friendly)
• CNC-machined from high-strength aluminum
• Best possible and effective protection for the clutch slave cylinder

• Extremely robust rear fastening clamp
• Made of 4 mm, high-tensile, robust aluminum
• Side parts welded from the inside and outside
• Extremely durable and endurance tested for the toughest off road use
• Custom design - specifically developed for KTM models
• Highest grade quality workmanship
• Simple and quick assembly

• Exceptionally robust rear fastening clamp
• Made of 4 mm strong, high-tensile, robust aluminum
• Extremely durable and endurance-tested for the toughest off-road use
• Custom design - specifically developed for KTM models
• Highest grade quality workmanship
• Simple and quick assembly

• Manufactured using state-of-the-art plastic injection moulding technology
• Made from special high-strength plastic
• Revised, extremely tough fastening system
• Developed for use in the toughest offroad terrain
• Maximum protection at minimum possible weight
• Precisely fitting design - specially developed for KTM models
• Simple installation making use of a special quick-release mechanism
• Removed in five seconds flat

• to make the mounting of the wrap-around handguard kit 79702984044 resp. of the Handguard kits 7970297900030 / 28 / AB / EB easier
• increases the space between alu-guard and hand brake cylinder

• CNC-machined from high-strength aluminum
• Lifting of the front wheel when starting is largely prevented
• Ensures more traction at the rear wheel

• Made from high-grade aluminum
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility - precisely customized to the WP fork
• Specially optimized geometry of the fork clamping
• No ovalization of the fork outer tube
• Highly precise and smooth fork response
• Maximum gain in handling and, at the same time, stability in the front wheel with overall more homogeneous effects of force in the complete vehicle
• Very simple offset adjustment of 20 or 22 mm
• Shorter offset: Stability on fast straights
• Longer offset: easier and quicker cornering in curves
• Including steering stem with steering head bearing already pressed on

For use on Enduro models, please order one of the following set articles: 00010000295 or 00010000296 or 00010000297

• Quick preload adjustment
• Use of the entire thread length on the shock absorber
• Very simple to use
• Low weight
• dust-resistant
• Mechanical drive mechanism

Supplied with fuel tank cap. IMS Dry break system mountable

• When mounting on SX models with Pro Lever linking, the right filter box cover 772.06.004.000/04/28/30 is also required
• Comes without a filler cap and fuel pump

• Two different heights possible
• Can be used as a stand for the quickfill system
• Storage space for the front and rear axle when removing the wheels
• Attachments for the following parts: mud removal tool, exhaust plug, magnetic bolt pan and various tools

• two tools in one, saves space during transport of your bike
• stabilizes the motorcycle during transport
• protects the fork shaft sealing rings and fork springs against damage, which may otherwise be caused by being tied down with too much force during transport

After transport it serves as the perfect plug-in stand!

• Easy handling and operation
• More safety
• Less wear on the cord
• Made of high quality material
• Cable not included

Patented gage for three important checks:

• Check and adjust chain tension
• Check chain lengthening (wear)
• Check positioning of rear wheel axle

• Contents are in accordance with DIN standard 13167-2014 for motorcyclists
• Waterproof packaging
• With its slim shape and Velcro straps at the back, the first aid kit is easy to store

Note:

It is mandatory to carry a first aid kit in many countries (such as Austria, Italy, Portugal and Spain).

The optimum solution for always having the most important tools to hand when on the road.

• Ratchet (with locking device), lever, two extensions and socket wrench
• Hexagon sockets from 6 to 24
• Allen keys from 3 to 10
• Phillips and slotted bits
• Torx bits from 15 to 55

• Ratchet (with locking device), lever, two extensions and socket wrench
• Hexagon sockets from 4 to 14
• Allen keys from 3 to 8
• Phillips, slotted and Torx bits

• Push-on spoke wrenches in sizes 5.65 and 6.95 mm
• Push-on ratchet ¼"
• Ratchet attachments: 6, 8, 10 mm socket wrench, 15 Torx

• Stabilizes your motorcycle during transportation
• Protects the fork shaft seal rings and fork springs from damage due to overly strong tightening down with lashing straps while transportation
• Gets clamped in between the tyre and the bottom of the front wheel fender

• Enables secure attachment to the machine without scratching your handlebars or tank
• With rubberized hooks and handlebar loops on belt ends
• 2 units

• Enables secure attachment to the machine without scratching your handlebars or tank
• Made from durable ballistic nylon
• Load capacity of 280 kg
• With handlebar loops
• With rubberized hooks on both belt ends

• Enables secure fastening to the machine without scratching your handlebars or tank
• Made from durable ballistic nylon
• Load capacity of 280 kg
• With handlebar loops
• With a rubberized hook and a carabiner on the belt ends
• 2 units

• Made from polyester, with special rubberized back
• Gas and oil resistant
• In special KTM design
• Size: 100 x 170 cm

• 10 pcs. cleanig towels, packed separately
• towel size 285 x 200 mm
• 70% Isopropanol
• ideal for cleaning of surfaces before application of stickers