• Acts as an additional protective layer
• Recommended for extremely dusty conditions
• Premature sanding of the air filter is avoided
• Coarse-pored air filter cover

• Approvals: CCCUO_EU
• Colour: White

• Recommended for extremely dusty conditions

• Approvals: CCCUO_EU

• Recommended in extremely wet conditions.

• Approvals: CCCUO_EU

• CNC milled from high-strength solid aluminum
• Chrome-plated pad guide pins on the brake caliper
• The benefits:
  
  • Reduced brake pad canting, hence no uneven wear
  • Constant braking feel, irrespective of brake pad wear or temperature
  • No vibration from the brake

Fitting possible on SX/EXC models without adapter, with the original hand pump and brake hose.
Can only be fitted with a 17"or 16.5" front wheel. 310 mm brake disc 586.09.060.000 or 250.09.260.000 required.
In combination with brake disc 25009260000 (310 mm) no speedometer signal will be sent.

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• High stiffness and strength
• Made of high-quality carbon
• Optimal protection against stone impact
• Visual highlight
• Optimal protection against stone impact

• Approvals: HOMNN_EU
• Surface (PowerParts): Matte finish
• Material (PowerParts): Carbon

• Clear pressure point across the entire temperature range
• More brake power
• Higher stiffness with the same weight
• Made of high-strength aluminum

• Approvals: CCCUO_EU
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Aluminium
• Alignment: Rear

• Clear pressure point across the entire temperature range
• More brake power
• Higher stiffness with the same weight
• Made of high-strength aluminum

• Approvals: CCCUO_EU
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Aluminium
• Alignment: Front

• Outer ring made of stainless high-performance brake steel
• Larger diameter for added braking performance

• Approvals: CCCUO_EU
• Diameter: 320 mm
• Material (PowerParts): Stainless steel

• No fading
• Outer ring made of stainless high-performance brake steel
• Minimal wear on brake pads
• Significantly longer lasting
• With Flame design for added braking performance

• Approvals: ABE
• Diameter: 220
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Stainless steel
• Alignment: Rear

• Floating
• Outer ring made of stainless high-performance brake steel
• Minimal wear on brake pads
• With Flame design for added braking performance

• Approvals: ABE
• Colour: Black
• Diameter: 260
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Aluminium

• Floating
• Outer ring made of stainless high-performance brake steel
• Inner ring anodised
• Minimal wear on brake pads
• With Flame design for added braking performance

• Up to 20% weight saving compared to stock components;
• Incl. the required CNC machined, black anodized brake caliper support for Brembo brake systems

• Approvals: ABE
• Colour: Black
• Diameter: 270 mm
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Front

• Floating
• Outer ring made of stainless high-performance brake steel
• Inner ring anodised
• Minimal wear on brake pads

• Approvals: EC-V
• Colour: Black
• Diameter: 260 mm
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Front

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Approvals: CCCUO_EU
• Material (PowerParts): Organic
• Alignment: Front

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

• Approvals: CCCUO_EU
• Material (PowerParts): Sinter
• Alignment: Front

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

• Approvals: CCCUO_EU
• Material (PowerParts): Sinter
• Alignment: Rear

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Approvals: CCCUO_EU
• Material (PowerParts): Organic
• Alignment: Rear

• With return valve
• Anodised dust protection cap
• Quick and easy bleeding of the brake

• Approvals: HOMNN_EU
• Colour: Orange
• Material (PowerParts): Aluminium
• Alignment: Front

• With return valve
• Anodised dust protection cap
• Quick and easy bleeding of the brake

• Approvals: HOMNN_EU
• Colour: Orange
• Material (PowerParts): Aluminium
• Alignment: Front

• Made of high-strength aluminum
• Improved braking performance

• Only for Brembo brake systems.
• Required for using the 320 mm brake disc 58309060000 with Brembo brake caliper

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• Protects the brake disc in the event of a fall
• High stiffness and strength
• Protects the rear brake disc from stones and other solid obstacles
• CNC milled from high-strength aluminum
• Lighter than series components

• Approvals: CCCUO_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Rear

• Manufactured using state-of-the-art 2-component injection molding technology
• Extremely light
• Protects the brake disc from stones and other solid obstacles
• Central adapter replaces the spacer sleeve on the wheel axle
• Allows tyre changes, brake service etc. without removing the brake cover

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic
• Alignment: Front

• Manufactured using state-of-the-art 2-component injection molding technology
• Extremely light
• Protects the brake disc from stones and other solid obstacles
• Central adapter replaces the spacer sleeve on the wheel axle
• Allows tyre changes, brake service etc. without removing the brake cover
• Noble material mix of carbon fiber and plastic

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Carbon

• Allows the rear wheel to be braked with the left hand
• Provides additional control in critical riding situations
• For use with the automatic clutch

• Only fits for Brembo and Magura brake systems
• To mount it on Braketec 70013071000 have to be used.

• Approvals: CCCUO_EU

• Protects the brake pedal from bending by branches

• Approvals: HOMNN_EU

• Perfect fit
• Made of high-quality carbon
• Optimal protection against stone impact

• Only for Brembo systems

• Approvals: HOMNN_EU
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Carbon

• For all 48 mm forks
• Made of high-quality carbon

• Approvals: HOMNN_EU
• Material (PowerParts): Carbon

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Black

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability
• Visual highlight

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Electronic orange

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability
• Visual highlight

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Gold

• Greater flexibility and better running characteristics
• Constant and permanent lubrication
• Better sealing against water and dirt
• Significantly longer durability

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Black

• Greater flexibility and better running characteristics
• Constant and permanent lubrication
• Better sealing against water and dirt
• Significantly longer durability

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Electronic orange

In orange Factory look.

• Approvals: HOMNN_EU
• Colour: Orange
• Alignment: Bottom

• Approvals: HOMNN_EU
• Colour: Orange

• Visual highlight
• Race look

• Approvals: HOMNN_EU
• Colour: Black

• Highest quality workmanship
• The right combination of look, style, and performance
• Specially designed for the challenges of off-road use
• Made from special, high-strength plastic for maximum stability
• With exchangeable chain track surface, therefore extremely durable

• Approvals: HOMNN_EU

• Prevents the chain from hitting the rear tyre
• Perfect chain guide, no branches drawn in between chain and engine housing

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Race look
• Visual highlight
• With exchangeable chain track surface, therefore extremely durable
• Specially designed for the challenges of off-road use

• CNC machined out of teflon

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING

• With exchangeable chain track surface, therefore extremely durable
• Specially designed for the challenges of off-road use
• Visual highlight
• Race look

• Approvals: HOMNN_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING

• Resistant to the toughest stresses and strains
• Forged lightening indents reduce rotational mass
• Grooves between the teeth clear dirt under the chain
• Extends chain life

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Steel
• Number Of Teeth: 13 teeth

• Significantly longer durability
• Teeth made of high-strength steel, for an extra long service life
• Extremely low-wear
• Recommended for long journeys

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Steel
• Number Of Teeth: 49 teeth

• Specially designed for the challenges of off-road use
• Significantly longer durability
• Made of high-strength aluminum
• The right combination of look, style, and performance

• The lightest Renthal Sprocket on the market
• Provide maximum power transfer and long-life due to advanced tooth profile and perfect concentricity
• Combination of a high strength base material and exceptionally hardwearing surface

• Approvals: HOMNN_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Number Of Teeth: 45 teeth

• Specially designed for the challenges of off-road use
• Significantly longer durability
• Made of high-strength aluminum
• The right combination of look, style, and performance

• The lightest Renthal Sprocket on the market
• Provide maximum power transfer and long-life due to advanced tooth profile and perfect concentricity
• Combination of a high strength base material and exceptionally hardwearing surface

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Number Of Teeth: 44 teeth

• Teeth made of high-strength steel, for an extra long service life
• Aluminum center section, reduces unsprung masses
• Permanently joined together with high-strength rivets
• At least three times longer service life than other aluminum rear sprockets
• 50 % lighter than steel rear sprockets
• Longer service life of the entire drivetrain kit

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Number Of Teeth: 46 teeth

• Teeth made of high-strength steel, for an extra long service life
• Aluminum center section, reduces unsprung masses
• Permanently joined together with high-strength rivets
• At least three times longer service life than other aluminum rear sprockets
• 50 % lighter than steel rear sprockets
• Longer service life of the entire drivetrain kit

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Number Of Teeth: 50 teeth

• Provides more traction when starting
• Made of high-strength aluminum
• Elegant anodised surface
• Pure race feeling
• Mounted directly on the OEM-fork

• Two different selectable preloads, without additional effort in mounting
• Simple mounting of the fork ring due to two part design
• No longer necessary to remove the fork

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU

• Made of the highest quality materials
• Tested in the toughest conditions
• Developed together with the vehicle
• Enables shorter drivers to also achieve the optimum seat height
• Perfect compromise between maximum chassis performance and lowest possible vehicle height
• No restrictions on riding dynamics

• Approvals: CCCUO_EU
• Height (PowerParts): -50

• Toolless adjustment of the spring preload

• Approvals: HOMNN_EU

Color differences between the upper and lower triple clamp cannot be technically ruled out.

• CNC milled aluminum triple clamp
• Elegant anodised surface
• Visual highlight
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility – precisely customised to the WP fork
• Specially optimised geometry of the fork clamping
• No ovalization of the fork outer tube
• Highly precise and smooth fork response
• Maximum handling gain
• Gain in stability at the front wheel
• Overall, more homogeneous force flows in the entire vehicle
• Simple offset adjustment
• Including steering stem with steering head bearing already pressed on

• Very simple offset adjustment of 20 or 22 mm
• Shorter offset: Stability on fast straights
• Longer offset: easier and quicker cornering in curves
• For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

Color differences between the upper and lower triple clamp cannot be technically ruled out.

• Approvals: CCCUO_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

Color differences between the upper and lower triple clamp cannot be technically ruled out.

• Elegant anodised surface
• Visual highlight
• CNC milled aluminum triple clamp
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility – precisely customised to the WP fork
• Including steering stem with steering head bearing already pressed on

• Handlebar mount kit 78901939044/144/244/344/444 or
• PHDS SXS07125200

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Offset: 20

Color differences between the upper and lower triple clamp cannot be technically ruled out.

• Elegant anodised surface
• Visual highlight
• CNC milled aluminum triple clamp
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility – precisely customised to the WP fork
• Including steering stem with steering head bearing already pressed on

• Handlebar mount kit 78901939044/144/244/344/444 or
• PHDS SXS07125200

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Offset: 22

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Front

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Rear

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Easy to mount
• Visual highlight
• Suitable for the left and right side

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight

• +8 mm at 125/150 SX/XC-W, SX-F, 450/500 EXC-F
• +16 mm at 250/300 SX/EXC, 250/350 EXC-F

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Includes drilling for safety wire
• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight
• Includes drilling for safety wire

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Protects the radiator from mud, dirt and sand
• Protection against rapid overheating of the engine in muddy conditions
• For extremely muddy conditions

• Approvals: HOMNN_EU

• Provides maximum protection at the lowest possible weight
• Including adapted radiator protection grills
• Easy to mount
• Optimal protection against stone impact

• Approvals: HOMNN_EU
• Colour: Black

• Suitable for the left and right side
• Provides maximum protection at the lowest possible weight
• Optimal protection against stone impact
• Easy to mount

• Approvals: HOMNN_EU
• Colour: White

• Protects the radiator from mud, dirt and sand
• Protection against rapid overheating of the engine in muddy conditions
• For extremely muddy conditions

• Approvals: HOMNN_EU

• Coolant resevoir for overheated radiators
• To be installed in the frame breast pipe

• Approvals: HOMNN_EU
• Colour: Black
• Height (PowerParts): -25

• Provides more air
• Maximum performance
• Digital control
• Current temperature can be read at any time
• Variable switch-on temperature between 65 °C and 95 °C
• Switch-off temperature 1 °C below the selected switch-on temperature
• Provides better cooling of the engine

• Approvals: HOMNN_EU

• Improves clutch performance and durability
• Hinson-typical surface treatment for significantly improved robustness compared to the standard part
• Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled
• Can be installed in the standard clutch or in combination with other Hinson clutch components
• CNC milled from high-strength aluminum
• Improves heat dissipation

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Improves clutch performance and durability
• Hinson-typical surface treatment for significantly improved robustness compared to the standard part
• Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled
• Can be installed in the standard clutch or in combination with other Hinson clutch components
• CNC milled from high-strength aluminum
• Improves heat dissipation

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Uncompromising race look
• CNC milled from high-strength aluminum
• Resistant to the toughest stresses and strains
• Elegant anodised surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Installed in the standard clutch, which means simple, uncomplicated and fast installation
• Unlimited and total concentration on the perfect line
• New generation of Rekluse centrifugal clutch with EXP technology
• Easily adjustable from the outside via the clutch slave cylinder
• No stalling of the engine in critical situations, such as braking, downhill runs, jumping, or when starting or pushing
• Improved traction, controllable by the throttle alone
• Slippery, extremely steep sections can be managed more easily > saves time and ensures faster lap times
• More relaxed, fatigue-free and controlled riding, even over longer distances and in tough terrain
• No more coupling is required, although it is still possible
• Special rear brake conversion kit available, allowing braking of the rear wheel with the left hand
• Tested in the toughest conditions

• Approvals: HOMNN_EU

• High stiffness and strength
• 80 % lighter than steel with the same load-bearing capacity
• Elegant look
• Low thermal expansion
• Made of high-quality carbon
• High long-term temperature stability
• Non-corrosive
• Maximum protection against falls, flying stones, branches, etc.
• Can only be fitted with a standard header

• Approvals: HOMNN_EU
• Surface (PowerParts): Glossy finish
• Material (PowerParts): Carbon

• Coated neoprene ring
• Simply pulled over the grips

• Approvals: HOMNN_EU
• Colour: Orange

• Made of high-strength aluminum
• Specially developed for extreme conditions
• Makes it easier to stand your motorcycle up

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Warm hands, no matter what the weather

• Approvals: HOMNN_EU

• Developed according to the requirements of our factory drivers
• Less stress when riding
• Objective: comfort AND safety
• Ergonomic contour adapted to the shape of the hand for maximum comfort
• Half waffle grip
• For a secure grip
• Three areas for the metal wire locking
• Version: medium

• Approvals: HOMNN_EU
• Colour: Grey
• Note: Closed end

• Developed according to the requirements of our factory drivers
• Less stress when riding
• Objective: comfort AND safety
• Ergonomic contour adapted to the shape of the hand for maximum comfort
• Half waffle grip
• For a secure grip
• Three areas for the metal wire locking
• Version: soft

• Approvals: HOMNN_EU
• Colour: Grey
• Note: Closed end

• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• Approvals: HOMNN_EU
• Colour: Black
• Note: Closed end

• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• Approvals: HOMNN_EU
• Colour: Black
• Note: Open end

• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• Approvals: HOMNN_EU
• Colour: Grey
• Note: Open end

• Specially developed for extreme conditions
• Strap made from high-strength nylon
• Makes it easier to stand your motorcycle up

• High-strength nylon strap
• Indispensable for use on extreme terrain
• Makes it easy to get your bike upright
• Attaches to rear frame

• Approvals: HOMNN_EU
• Colour: Black
• Alignment: Rear

• Makes it easier to stand your motorcycle up
• Specially developed for extreme conditions
• Strap made from high-strength nylon

• Approvals: HOMNN_EU
• Colour: Black
• Alignment: Front

• A motorcycle hand grip can be mounted on the handle (not included)

• Approvals: HOMNN_EU

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Attached directly at the levers with a special mounting
• Only mountable with Brembo brake system

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Attached directly at the levers with a special mounting
• Only mountable with Brembo brake system

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Attached directly at the levers with a special mounting
• Only mountable with Brembo brake system

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Attached directly at the levers with a special mounting

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Plastic

• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic
• Excellent weather protection

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Excellent weather protection
• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Ceramic white
• Material (PowerParts): Plastic

• Excellent weather protection
• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Ceramic white
• Material (PowerParts): Aluminium

• Uncompromising race look
• Extremely light
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Excellent weather protection
• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Uncompromising race look
• Extremely light
• Open design

• Attached directly at the levers with a special mounting.
• Only mountable with Brembo brake system

• Approvals: HOMNN_EU
• Colour: Orange
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design

• Attached directly at the levers with a special mounting.
• Only mountable with Brembo brake system

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Uncompromising race look
• Extremely light
• Open design

• Approvals: HOMNN_EU
• Colour: White
• Material (PowerParts): Plastic

• Never again cold fingers!
• Mounting over handlebar and switches
• Better control during winter ride-outs

• Approvals: HOMNN_EU

• Extremely sturdy aluminum brackets
• Prevents broken levers
• Including all required assembly materials

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• Made of robust plastic
• To convert the open, standard handguards to a closed version

• Usable with handguards 7960297900028/30AB and 2650297900028/30/AB

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Extremely sturdy aluminum brackets
• Prevents broken levers
• Including all required assembly materials

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Made of robust plastic
• Fastening independent of fittings directly on the handlebars
• To convert the open, standard handguards to a closed version

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Made of robust plastic
• Fastening independent of fittings directly on the handlebars
• To convert the open, standard handguards to a closed version

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Made of robust plastic
• Fastening independent of fittings directly on the handlebars
• To convert the open, standard handguards to a closed version

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Made of robust plastic
• Fastening independent of fittings directly on the handlebars
• To convert the open, standard handguards to a closed version

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Plastic

• Approvals: EC-V
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Height (PowerParts): 37

• Approvals: CCCUO_EU
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Height (PowerParts): 20

• Approvals: CCCUO_EU
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Height (PowerParts): 20

• CNC milled handlebar mount with damping rubber inserts
• Gentle on wrists and shoulder joints
• Damping of hard shocks
• Absorption of chassis and engine vibrations
• Additional handlebar damping in horizontal direction
• Optimum steering precision
• Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment

• Handlebar height adjustable to 2 positions

• Approvals: EC-V
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Made of high-strength aluminum
• Tested in complex and specially-developed test cycles
• Position markings for easy adjustment

• Dimensions: A = 115 mm, B = 806 mm, C = 62 mm

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• When locked, the crossbar is solid (stiff)
• When unlocked, the crossbar is flexible

Dimensions: A = 112 mm, B = 811 mm, C = 88 mm

• Approvals: CCCUO_EU
• Diameter: 28 mm
• Factory Racing: USED BY FACTORY RACING

• The Twinwall, in the KTM orange design
• Two handlebars in one
• The exterior ensures maximum resistance to external damage (e.g. fall)
• Additionally hard anodised against corrosion
• The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls.
• Nylon inserts in the inner tube allow thinner walls
• Very good flex properties
• Comes with handlebar pad

• Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

• Approvals: CCCUO_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Two handlebars in one
• The exterior ensures maximum resistance to external damage (e.g. fall)
• Additionally hard anodised against corrosion
• The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls.
• Nylon inserts in the inner tube allow thinner walls
• Very good flex properties
• Comes with handlebar pad

Renthal Twinwall 996

• Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

• Approvals: CCCUO_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• The Twinwall, in the KTM orange design
• Two handlebars in one
• The exterior ensures maximum resistance to external damage (e.g. fall)
• Additionally hard anodised against corrosion
• The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls.
• Nylon inserts in the inner tube allow thinner walls
• Very good flex properties
• Comes with handlebar pad

• Dimensions: A = 104 mm, B = 811 mm, C = 74 mm

• Approvals: CCCUO_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Enables power consumers such as grip heater or radiator fans to be installed on motocross or cross-country models as well

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU

• Ignition curve adjustment made easy!
• Comfortable ignition curve adjustment on the handlebar

• Approvals: CCCUO_EU

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight with technical and ergonomic added value
• Adjustable grip width

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Visual highlight with technical and ergonomic added value
• Ergonomically perfect shape (the result of years of racing experience)
• Adjustable grip width

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Weight: 0.055

• Elegant anodised surface
• Visual highlight with technical and ergonomic added value
• Flaps removed on ground contact
• Prevents broken levers

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium