This large-pore air filter cover acts as an additional protective layer, hence extending the filter service interval. Recommended in extremely dusty conditions.

• Approvals: CCCUO_EU

• Approvals: CCCUO_EU

Recommended in extremely wet conditions.

• Approvals: CCCUO_EU

• CNC milled from high-strength solid aluminum
• Chrome-plated pad guide pins on the brake caliper
• The benefits:
  
  • Reduced brake pad canting, hence no uneven wear
  • Constant braking feel, irrespective of brake pad wear or temperature
  • No vibration from the brake

Fitting possible on SX/EXC models without adapter, with the original hand pump and brake hose.
Can only be fitted with a 17"or 16.5" front wheel. 310 mm brake disc 586.09.060.000 or 250.09.260.000 required.
In combination with brake disc 25009260000 (310 mm) no speedometer signal will be sent.

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Made of high-quality carbon
• Visual highlight
• Optimal protection against stone impact
• High stiffness and strength
• Optimal protection against stone impact

• Approvals: HOMNN_EU
• Surface (PowerParts): Matte finish
• Material (PowerParts): Carbon

• Made of high-strength aluminum
• Clear pressure point across the entire temperature range
• More brake power
• Higher stiffness with the same weight

• Approvals: CCCUO_EU
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Aluminium
• Alignment: Rear

• Made of high-strength aluminum
• Clear pressure point across the entire temperature range
• More brake power
• Higher stiffness with the same weight

• Approvals: CCCUO_EU
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Aluminium
• Alignment: Front

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Made of high-strength aluminum
• Perfect dosing capacity
• Requires significantly less manual force
• Larger piston than standard

• Radial hand brake cylinder with 16 mm piston
• Allows better leverage than conventional brake cylinders

• Approvals: CCCUO_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Outer ring made of stainless high-performance brake steel
• Larger diameter for added braking performance

• Approvals: CCCUO_EU
• Diameter: 320 mm
• Material (PowerParts): Stainless steel

• Floating brake disc manufactured from special high-grade stainless steel
• With Flame design for added braking performance
• Minimal wear on brake linings

• Approvals: ABE
• Diameter: 260 mm
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Stainless steel

• No fading
• Outer ring made of stainless high-performance brake steel
• Minimal wear on brake pads
• Significantly longer lasting
• With Flame design for added braking performance

• Approvals: ABE
• Diameter: 220 mm
• Material (PowerParts): Stainless steel

• No fading
• Outer ring made of stainless high-performance brake steel
• Minimal wear on brake pads
• Significantly longer lasting
• With Flame design for added braking performance

• Approvals: ABE
• Diameter: 220 mm
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Stainless steel
• Alignment: Rear

• Floating
• Outer ring made of stainless high-performance brake steel
• Inner ring anodized
• Minimal wear on brake pads
• With Flame design for added braking performance

• Up to 20% weight saving compared to stock components;
• Incl. the required CNC machined, black anodized brake caliper support for Brembo brake systems

• Approvals: ABE
• Colour: Black
• Diameter: 270 mm
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Front

• Floating
• Outer ring made of stainless high-performance brake steel
• Inner ring anodized
• Minimal wear on brake pads
• Larger diameter for added braking performance

• Can only be used in conjunction with 4 piston brake caliper 5841301564404 or 6 piston brake caliper 5941301504404
• In combination with 4 piston brake caliper 58413015644/04 no speedometer signal will be sent

• Approvals: CCCUO_EU
• Colour: Black
• Diameter: 310 mm
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Front

• Minimal wear on brake pads
• Significantly longer lasting
• Full version for muddy track conditions

• Approvals: CCCUO_EU
• Diameter: 220 mm
• Material (PowerParts): Stainless steel

• Floating
• Outer ring made of stainless high-performance brake steel
• Inner ring anodized
• Minimal wear on brake pads

• Approvals: EC-V
• Colour: Black
• Diameter: 260 mm
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Front

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Approvals: CCCUO_EU
• Material (PowerParts): Organic
• Alignment: Rear

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

• Approvals: CCCUO_EU
• Material (PowerParts): Sinter
• Alignment: Rear

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Approvals: CCCUO_EU
• Material (PowerParts): Organic
• Alignment: Front

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

• Approvals: CCCUO_EU
• Material (PowerParts): Organic
• Alignment: Front

• With return valve
• Anodized dust protection cap
• Quick and easy bleeding of the brake

• Approvals: HOMNN_EU
• Colour: Orange
• Material (PowerParts): Aluminium
• Alignment: Front

• With return valve
• Anodized dust protection cap
• Quick and easy bleeding of the brake

• Approvals: HOMNN_EU
• Colour: Orange
• Material (PowerParts): Aluminium
• Alignment: Front

• Made of high-strength aluminum
• Improved braking performance

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Lighter than series components
• Protects the brake disc in the event of a fall
• High stiffness and strength
• Protects the rear brake disc from stones and other solid obstacles

• Approvals: CCCUO_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Rear

• CNC milled from high-strength aluminum
• Lighter than series components
• Protects the brake disc in the event of a fall
• High stiffness and strength
• Protects the rear brake disc from stones and other solid obstacles

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Rear

• CNC milled from high-strength aluminum
• Lighter than series components
• Protects the brake disc in the event of a fall
• High stiffness and strength
• Protects the rear brake disc from stones and other solid obstacles

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Rear

• CNC milled from high-strength aluminum
• Lighter than series components
• Protects the brake disc in the event of a fall
• High stiffness and strength
• Protects the rear brake disc from stones and other solid obstacles

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Rear

• Replaces the standard pins
• Quick and easy brake pad change even in difficult conditions

• Approvals: HOMNN_EU
• Material (PowerParts): Steel

• Increases the volume of the rear master cylinder
• Additional cooling ribs minimize the heating of the brake fluid
• Eliminates “fading” almost completely

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Rear

• Protects the brake pedal from bending by branches

• Approvals: HOMNN_EU

• For all 48 mm forks
• Made of high-quality carbon

• Approvals: HOMNN_EU
• Material (PowerParts): Carbon

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Black

• Visual highlight
• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Gold

• Visual highlight
• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Electronic orange

• Greater flexibility and better running characteristics
• Constant and permanent lubrication
• Better sealing against water and dirt
• Significantly longer durability

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Black

• Greater flexibility and better running characteristics
• Constant and permanent lubrication
• Better sealing against water and dirt
• Significantly longer durability

• Approvals: HOMNN_EU
• Number Of Chain Links: 118
• Chain Pitch: 520
• Colour: Electronic orange

• Recommended for long journeys
• Significantly longer durability
• Teeth made of high-strength steel, for an extra long service life
• Extremely low-wear

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Steel
• Number Of Teeth: 42 teeth

• Elegant anodized surface
• Extremely light
• Made of high-strength aluminum
• Visual highlight
• Precisely ground to 0.002 mm, dead straight and impact-free chain track
• Free from vibration – therefore the highest power transmission efficiency
• Reduces the rotating masses

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Number Of Teeth: 50 teeth

• Teeth made of high-strength steel, for an extra long service life
• Aluminum center section, reduces unsprung masses
• Permanently joined together with high-strength rivets
• At least three times longer service life than other aluminum rear sprockets
• 50 % lighter than steel rear sprockets
• Longer service life of the entire drivetrain kit

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Number Of Teeth: 41 teeth

• Teeth made of high-strength steel, for an extra long service life
• Aluminum center section, reduces unsprung masses
• Permanently joined together with high-strength rivets
• At least three times longer service life than other aluminum rear sprockets
• 50 % lighter than steel rear sprockets
• Longer service life of the entire drivetrain kit

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Number Of Teeth: 45 teeth

• Teeth made of high-strength steel, for an extra long service life
• Aluminum center section, reduces unsprung masses
• Permanently joined together with high-strength rivets
• At least three times longer service life than other aluminum rear sprockets
• 50 % lighter than steel rear sprockets
• Longer service life of the entire drivetrain kit

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Number Of Teeth: 38 teeth

• Approvals: HOMNN_EU
• Colour: Orange
• Alignment: Bottom

In orange Factory look.

• Approvals: HOMNN_EU
• Colour: Orange
• Alignment: Bottom

• Approvals: HOMNN_EU
• Colour: Orange

• Visual highlight
• Race look

• Approvals: HOMNN_EU
• Colour: Black

• Made of high-strength aluminum

• Protects the chain guide bracket against damage

• Approvals: HOMNN_EU
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Prevents the chain from hitting the rear tyre
• Perfect chain guide, no branches drawn in between chain and engine housing

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Synthetic material

• Visual highlight
• Race look
• With exchangeable chain track surface, therefore extremely durable
• Specially designed for the challenges of off-road use

• Approvals: HOMNN_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING

• Developed together with the vehicle
• Specially developed for WP forks
• Fork bleeding using finger pressure

• Approvals: HOMNN_EU

• Elegant anodized surface
• Visual highlight
• CNC milled aluminum triple clamp
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility – precisely customized to the WP fork
• Specially optimized geometry of the fork clamping
• No ovalization of the fork outer tube
• Highly precise and smooth fork response
• Maximum handling gain
• Gain in stability at the front wheel
• Overall, more homogeneous force flows in the entire vehicle
• Simple offset adjustment
• Including steering stem with steering head bearing already pressed on

• Very simple offset adjustment of 20 or 22 mm
• Shorter offset: Stability on fast straights
• Longer offset: easier and quicker cornering in curves
• For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

• Approvals: CCCUO_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Elegant anodized surface
• Visual highlight
• CNC milled aluminum triple clamp
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility – precisely customized to the WP fork
• Specially optimized geometry of the fork clamping
• No ovalization of the fork outer tube
• Highly precise and smooth fork response
• Maximum handling gain
• Gain in stability at the front wheel
• Overall, more homogeneous force flows in the entire vehicle
• Simple offset adjustment
• Including steering stem with steering head bearing already pressed on

• Very simple offset adjustment of 20 or 22 mm
• Shorter offset: Stability on fast straights
• Longer offset: easier and quicker cornering in curves
• For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

• Approvals: CCCUO_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Quick preload adjustment
• Use of the entire thread length on the shock absorber
• Very simple to use
• Low weight
• dust-resistant
• Mechanical drive mechanism

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• Elegant anodized surface
• Visual highlight
• CNC milled aluminum triple clamp
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility – precisely customized to the WP fork
• Including steering stem with steering head bearing already pressed on

• Handlebar mount kit 78901939044/144/244/344/444 or
• PHDS SXS07125200

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Offset: 20

• Elegant anodized surface
• Visual highlight
• CNC milled aluminum triple clamp
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility – precisely customized to the WP fork
• Including steering stem with steering head bearing already pressed on

• Handlebar mount kit 78901939044/144/244/344/444 or
• PHDS SXS07125200

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Offset: 22

• CNC milled from high-strength aluminum
• Elegant anodized surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Front

• CNC milled from high-strength aluminum
• Elegant anodized surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Rear

• CNC milled from high-strength aluminum
• Elegant anodized surface
• Easy to mount
• Visual highlight
• Suitable for the left and right side

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodized surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodized surface

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodized surface
• Visual highlight
• Includes drilling for safety wire

• Approvals: HOMNN_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• For extremely muddy conditions
• Protects the radiator from mud, dirt and sand
• Protection against rapid overheating of the engine in muddy conditions

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU
• Colour: White

• Approvals: HOMNN_EU
• Colour: Black

• Specially matched to the standard cylinder head
• Matched to the use of 98 or higher octane fuel
• Higher peak power and rev speed
• More torque in the middle rev range
• Improved response behavior
• Best possible performance
• Recommended in combination with a factory exhaust system as well as a factory spark plug
• Application of the factory digital box on the KTM 125 EXC is only makes sense with a factory exhaust system

• Approvals: CCCUO_EU

• Specially developed for application in Motocross
• Made from high-grade aluminum
• With standard combustion chamber

• Approvals: CCCUO_EU
• Material (PowerParts): Aluminium

• Specially developed for extreme conditions
• Manufactured in a purpose developed alloy
• Enhanced performance from the engine due to the excellent conductivity of the material used with unchanged combustion chamber
• Reduces unwanted detonations in the cylinder, that in turn has a positive effect on the service life as well as on the performance of the engine

• Approvals: CCCUO_EU

• Minimal weight
• Maximum top-end performance
• Perfectly distributed torque curve
• Lowest noise level of any 2-stroke silencer
• Long service life

Combined with the original header, this Akrapovi? silencer is licensed for road use on 2012-16 EXC 2-stroke models (except for the 200 EXC).

• Approvals: CCCUO_EU
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Carbon

• Fat torque curve for optimal rideability
• Minimum weight and maximum performance
• Made from robust steel
• Untreated surface for an original factory look
• Rich, unmistakable sound
• Recommended in combination with a factory or Six Days silencer for a perfectly matched full system with optimum performance

• Approvals: CCCUO_EU

• Made from high quality, extra strong and durable sheet steel
• Nickel-plated surface
• Wide, even rev band
• High rev speed
• More traction and better control under full throttle
• Including O-rings
• Recommended in combination with an FMF silencer for a perfectly matched full system with optimum performance

• Approvals: CCCUO_EU

DID YOU ALREADY KNOW about the special properties of carbon fiber?

• Extremely light: 80% lighter than steel with the same strength
• Exceptionally stable: Four times more durable than aluminum
• Maximum stiffness and tensile strength
• Free from corrosion
• High longterm temperature durability
• Minimal heat expansion
• And not least of all it looks just cool

• Approvals: HOMNN_EU
• Material (PowerParts): Carbon

DID YOU ALREADY KNOW about the special properties of carbon fiber?

• Extremely light: 80% lighter than steel with the same strength
• Exceptionally stable: Four times more durable than aluminum
• Maximum stiffness and tensile strength
• Free from corrosion
• High longterm temperature durability
• Minimal heat expansion
• And not least of all it looks just cool

• Approvals: HOMNN_EU
• Material (PowerParts): Carbon

• For extremely muddy conditions

• Approvals: HOMNN_EU

• Move along with weight shift
• Permanent contact between boot and footpeg
• Extends the service life of your boots
• Enlarged tread area
• More control
• More curve pressure
• Easier and faster weight shifting
• Easier shifting and braking

Spring-mounted, 20-degree rotational movement possible towards front and rear

• Approvals: CCCUO_EU

• Coated neoprene ring
• Simply pulled over the grips

• Approvals: HOMNN_EU
• Colour: Orange

• Grip made of high-strength aluminum
• Essential for extreme off-road use
• Makes it easier to stand your motorcycle up
• Attached to the silencer support on the subframe

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Warm hands, no matter what the weather

• Approvals: HOMNN_EU

• Developed according to the requirements of our factory drivers
• Less stress when riding
• Objective: comfort AND safety
• Ergonomic contour adapted to the shape of the hand for maximum comfort
• Half waffle grip
• For a secure grip
• Three areas for the metal wire locking
• Version: soft

• Approvals: HOMNN_EU
• Colour: Grey
• Note: Closed end

• Developed according to the requirements of our factory drivers
• Less stress when riding
• Objective: comfort AND safety
• Ergonomic contour adapted to the shape of the hand for maximum comfort
• Half waffle grip
• For a secure grip
• Three areas for the metal wire locking
• Version: medium

• Approvals: HOMNN_EU
• Colour: Grey
• Note: Closed end

• Right grip permanently glued to the throttle grip
• Left grip with aluminum clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• Approvals: HOMNN_EU
• Colour: Black
• Note: Closed end

• For a secure grip
• Maximum grip on the hand grip even in extremely muddy conditions

• Approvals: HOMNN_EU
• Colour: Black

• Specially developed for extreme conditions
• Strap made from high-strength nylon
• Makes it easier to stand your motorcycle up

• Approvals: HOMNN_EU
• Colour: Black
• Alignment: Front

• High-strength nylon strap
• Indispensable for use on extreme terrain
• Makes it easy to get your bike upright
• Attaches to rear frame

• Approvals: HOMNN_EU
• Alignment: Rear

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Black center section = maximum strength for optimum protection
• Coloured upper and lower parts = highly flexible for enduring the roughest of treatment
• The choice is yours: attached directly to the handlebar with a plastic bracket or directly to the lever mounting with a special adaptor.
• Cannot be fitted with Twinwall handlebar.

Attached directly at the levers with a special mounting.

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING

• Extremely light
• Uncompromising race look
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Attached directly at the levers with a special mounting
• Only mountable with Brembo brake system

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Synthetic material

• Extremely light
• Uncompromising race look
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Mounting not possible with Twinwall handlebars

• Attached directly at the levers with a special mounting
• Only mountable with Brembo brake system

• Approvals: HOMNN_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Material (PowerParts): Synthetic material

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Excellent weather protection
• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers

• Approvals: HOMNN_EU
• Colour: Orange
• Material (PowerParts): Aluminium

• Excellent weather protection
• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers

• Approvals: HOMNN_EU
• Colour: White
• Material (PowerParts): Aluminium

• Excellent weather protection
• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Extremely light
• Uncompromising race look
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Extremely light
• Uncompromising race look
• Open design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Colored top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Excellent weather protection
• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Ceramic white
• Material (PowerParts): Synthetic material

• Maximum protection against falls, flying stones, branches, etc.
• Indispensable companion for heavy off-road and Supermoto use
• Excellent weather protection
• Wide, generous design in combination with sturdy aluminum bracket
• Prevents broken levers
• Made of robust plastic

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Never again cold fingers!
• Mounting over handlebar and switches
• Better control during winter ride-outs

• Approvals: HOMNN_EU

• Made of sturdy plastic
• Converts the originally open handguards into a closed version
• Mounting independed to the lever mounting, directly to the handlebar
• Compatible also with handguards 79602979000EB/28/30/AB and 72102979000EB/28/30

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Made of sturdy plastic
• Converts the originally open handguards into a closed version
• Compatible also with handguards 79602979000EB/28/30/AB and 72102979000EB/28/30

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Including all required assembly materials
• Extremely sturdy aluminum brackets
• Prevents broken levers

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• Made of robust plastic
• Fastening independent of fittings directly on the handlebars
• To convert the open, standard handguards to a closed version

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Made of robust plastic
• Fastening independent of fittings directly on the handlebars
• To convert the open, standard handguards to a closed version

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Made of robust plastic
• Fastening independent of fittings directly on the handlebars
• To convert the open, standard handguards to a closed version

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Made of robust plastic
• Fastening independent of fittings directly on the handlebars
• To convert the open, standard handguards to a closed version

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Approvals: CCCUO_EU
• Material (PowerParts): Aluminium

• Approvals: CCCUO_EU
• Material (PowerParts): Aluminium

• Approvals: EC-V
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Height (PowerParts): 37

• Approvals: CCCUO_EU
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Height (PowerParts): 12

• Approvals: CCCUO_EU
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Height (PowerParts): 20

• Approvals: CCCUO_EU
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Height (PowerParts): 30

• CNC milled handlebar mount with damping rubber inserts
• Gentle on wrists and shoulder joints
• Damping of hard shocks
• Absorption of chassis and engine vibrations
• Additional handlebar damping in horizontal direction
• Optimum steering precision
• Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment

• Handlebar height adjustable to 2 positions

• Approvals: EC-V
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Made of high-strength aluminum
• Tested in complex and specially-developed test cycles
• Position markings for easy adjustment

• Dimensions: A = 115 mm, B = 806 mm, C = 62 mm

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• The Twinwall, in the KTM orange design
• Two handlebars in one
• The exterior ensures maximum resistance to external damage (e.g. fall)
• Additionally hard anodized against corrosion
• The interior, made of a special alloy, is also hard anodized to protect it from damage by the handlebar controls.
• Nylon inserts in the inner tube allow thinner walls
• Very good flex properties
• Comes with handlebar pad

• Dimensions: A = 104 mm, B = 811 mm, C = 74 mm

• Approvals: CCCUO_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• The Twinwall, in the KTM orange design
• Two handlebars in one
• The exterior ensures maximum resistance to external damage (e.g. fall)
• Additionally hard anodized against corrosion
• The interior, made of a special alloy, is also hard anodized to protect it from damage by the handlebar controls.
• Nylon inserts in the inner tube allow thinner walls
• Very good flex properties
• Comes with handlebar pad

• Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

• Approvals: CCCUO_EU
• Colour: Orange
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Two handlebars in one
• The exterior ensures maximum resistance to external damage (e.g. fall)
• Additionally hard anodized against corrosion
• The interior, made of a special alloy, is also hard anodized to protect it from damage by the handlebar controls.
• Nylon inserts in the inner tube allow thinner walls
• Very good flex properties
• Comes with handlebar pad

Renthal Twinwall 996

• Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

• Approvals: CCCUO_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Enables power consumers such as grip heater or radiator fans to be installed on SX or XC as well

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU

• Know exactly when the next service is due

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU

• Ignition curve adjustment made easy!
• Comfortable ignition curve adjustment on the handlebar

• Approvals: CCCUO_EU

• Approvals: HOMNN_EU
• Material (PowerParts): Stainless steel

• CNC milled from high-strength aluminum
• Elegant anodized surface
• Visual highlight with technical and ergonomic added value
• The brake or clutch fitting rotates in the event of a fall
• Adjustable grip width

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Manufactured from high-strength aluminum, forged and then CNC-machined
• This extensive production process guarantees a long service life, maximum flexibility and a precise fit
• Ergonomically perfected shape (the result of years of racing experience)
• Predefined breaking point
• Orange anodized

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Elegant anodized surface
• Visual highlight with technical and ergonomic added value
• The brake or clutch fitting rotates in the event of a fall

• Approvals: CCCUO_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Elegant anodized surface
• Visual highlight with technical and ergonomic added value
• The brake or clutch fitting rotates in the event of a fall

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodized surface
• Visual highlight
• Including plastic insert
• The brake or clutch fitting rotates in the event of a fall
• Reduces the risk of a lever being broken

Suitable for all Brembo® and Formula brake and clutch assembles

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodized surface
• Visual highlight
• Prevents the hand grips from chafing in the event of a fall

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Already mandatory in many competitions
• Provides optimum protection
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange

• Already mandatory in many competitions
• Provides optimum protection
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange

• Exceptionally robust
• Extremely light

• Approvals: CCCUO_EU
• Colour: Black
• Alignment: Left

• Protects your expensive smartphone from rain, dust or mud
• Touchscreen remains fully functional
• Handlebar pad and smartphone holder in one
• Smartphone cover with velcro fastener attached to the handlebar pad
• Smartphone can be easily removed with its cover
• Optimal solution for quick and secure fastening of your smartphone on the vehicle

• For Smartphones up to 160 x 80 mm
• Comes with two separate protective strips in case the sleeve is not used
• Can also be fitted in combination with the PHDS-handlebar support
• Smartphone not included!

• Approvals: HOMNN_EU
• Colour: Orange

• Developed according to the requirements of our factory drivers
• Gain in stability at the front wheel
• High-end steering damper
• Maximum control on fast tracks
• Fully adjustable
• Well thought-out mounting of the damper enables individual handlebar adjustment
• Reduced weight
• Sensitive response behavior
• High speed DCC

• Optimum 25 click setting range.
• Proven success with the KTM Works Rally Team.
• For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

• Approvals: HOMNN_EU
• Colour: Gold
• Factory Racing: USED BY FACTORY RACING

• Top performance/price ratio
• Gain in stability at the front wheel
• Fully adjustable
• Well thought-out mounting of the damper enables individual handlebar adjustment

• 00050000929 handle bar support kit required for use on MY16 and on XC from MY16.
• For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Approvals: HOMNN_EU
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Resistant waterproof coating
• Waterproof roll closure
• For waterproof storage of documents, maps, cellphones, navigation devices etc.

• Approvals: HOMNN_EU
• Colour: Black
• Volume: 4

• Can be mounted without additional mounting material
• Welded seams
• Robust and waterproof bag
• Waterproof roll closure
• Resistant waterproof coating

• Approvals: HOMNN_EU
• Colour: Black
• Volume: 5

• For waterproof storage of documents, maps, cellphones, navigation devices etc.

• Approvals: HOMNN_EU
• Colour: Black

• Suitable for all Garmin GPS devices
• Suitable for all TomTom GPS devices
• Suitable for the Touratech iBracket
• Mounting on the standard handlebar clamps

• Approvals: HOMNN_EU
• Colour: Black

• Universally applicable for mounting the GPS bracket

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium

• Universal and inconspicuous bracket for your smartphone
• Optimal solution for quick and secure fastening of your smartphone on the vehicle

• Can be clamped on the handlebar (including different adaptor)
• The arm can be rotated in any position for the perfect position for your smartphone

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Aluminium

• Smartphone can be easily removed with its cover

• Protects your expensive smartphone

• Optimal solution for quick and secure fastening of your smartphone on the vehicle

• Approvals: HOMNN_EU
• Colour: Black
• Smartphone Bracket: IPhone 6/6S/7/8/SE

• Optimal solution for quick and secure fastening of your smartphone on the vehicle

• Dimensions: 66x55mm (2.6x2.17 inch)

• Approvals: HOMNN_EU

• Protects your expensive smartphone from rain, dust or mud
• Touchscreen remains fully functional
• Optimal solution for quick and secure fastening of your smartphone on the vehicle

• Approvals: HOMNN_EU
• Smartphone Bracket: 165 x 80 mm

• Elegant anodized surface
• Visual highlight
• CNC milled aluminum triple clamp
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility – precisely customized to the WP fork
• Specially optimized geometry of the fork clamping
• No ovalization of the fork outer tube
• Highly precise and smooth fork response
• Maximum handling gain
• Gain in stability at the front wheel
• Overall, more homogeneous force flows in the entire vehicle
• Simple offset adjustment
• Including steering stem with steering head bearing already pressed on

• Very simple offset adjustment of 20 or 22 mm
• Shorter offset: Stability on fast straights
• Longer offset: easier and quicker cornering in curves
• For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

• Approvals: CCCUO_EU
• Colour: Black
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Easy to mount
• Protects from damage in the event of a fall

• Approvals: HOMNN_EU
• Colour: Black
• Alignment: Rear

• Protects the footpegs from damage during a potential fall

• Approvals: HOMNN_EU
• Colour: Black

• For all 48 mm forks
• Ideal protection for sealing the fork
• For use with an open fork protector

• Approvals: HOMNN_EU

• For all 48 mm forks
• Ideal protection for sealing the fork
• For use with a closed fork protector

• Approvals: HOMNN_EU

• Approvals: HOMNN_EU
• Colour: Orange

• Approvals: CCCUO_EU

• Protects the lower PDS bearing against dirt permeation
• Extends the service life of the lower PDS bearing

• Approvals: HOMNN_EU

• For all 48 mm forks
• Extra strong film

• Approvals: HOMNN_EU
• Colour: Black
• Type: 8

• For all 48 mm forks
• Extra strong film

• Approvals: HOMNN_EU
• Colour: Transparent
• Type: 8

• Protects from damage in the event of a fall
• Permanent protection against unattractive scratches and matte spots on the swingarm

• Approvals: HOMNN_EU
• Colour: Black

• Approvals: HOMNN_EU
• Colour: Transparent

• Reduces dirt deposits between engine and skid plate
• Provides better cooling of the engine

• Approvals: HOMNN_EU
• Colour: Black
• Material (PowerParts): Synthetic material

• Manufactured using state-of-the-art plastic injection moulding technology
• Made from special high-strength plastic
• Revised, extremely tough fastening system
• Developed for use in the toughest offroad terrain
• Maximum protection at minimum possible weight
• Precisely fitting design - specially developed for KTM models
• Simple installation making use of a special quick-release mechanism
• Removed in five seconds flat

• Approvals: HOMNN_EU
• Colour: Black
• Weight: 0.554

• Extremely robust rear fastening clamp
• Made of 4 mm, high-tensile, robust aluminum
• Side parts welded from the inside and outside
• Extremely durable and endurance tested for the toughest off road use
• Custom design - specifically developed for KTM models
• Highest grade quality workmanship
• Simple and quick assembly

• Approvals: HOMNN_EU
• Material (PowerParts): Aluminium
• Weight: 0.992

• Approvals: HOMNN_EU
• Colour: Blue
• Factory Racing: USED BY FACTORY RACING

• Approvals: HOMNN_EU
• Colour: Black

• Approvals: HOMNN_EU
• Colour: Blue

• Approvals: HOMNN_EU
• Colour: Black

• Approvals: HOMNN_EU
• Colour: Black
• Height (PowerParts): +20

• Approvals: HOMNN_EU
• Height (PowerParts): -15

• Approvals: HOMNN_EU
• Colour: Black
• Height (PowerParts): +20

• Approvals: HOMNN_EU

• Made of high-strength aluminum
• Improved braking performance

• Approvals: HOMNN_EU
• Colour: Black
• Surface (PowerParts): Anodized

• Floating
• Inner ring anodized
• Outer ring made of stainless high-performance brake steel
• Minimal wear on brake pads
• With Flame design for added braking performance

• Approvals: ABE
• Colour: Black
• Diameter: 270 mm
• Factory Racing: USED BY FACTORY RACING
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium
• Alignment: Front

• CNC milled from high-strength aluminum
• Not lockable
• Extremely fast and keyless refueling

• Approvals: CCCUO_EU
• Colour: Black
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• CNC milled from high-strength aluminum
• Elegant anodized surface
• Visual highlight

• Approvals: HOMNN_EU
• Colour: Orange
• Surface (PowerParts): Anodized
• Material (PowerParts): Aluminium

• Prevents dust and dirt from entering the tank when the fuel tank cap is opened
• Filter is attached directly to the tank opening
• Fits all 3/4 fuel tank caps