The closed, two-component plastic handguards developed by KTM feature a black center section that offers maximum strength for optimum protection. The colorful upper and lower parts are highly flexible and endure even the roughest of treatment without complaint. Available in two different heights.

• Enables secure attachment to the machine without scratching your handlebars or tank
• Made from durable ballistic nylon
• Load capacity of 280 kg
• Dimensions: 3,8 cm x 0,6 m
• 2 units

• Enables secure attachment to the machine without scratching your handlebars or tank
• Made from durable ballistic nylon
• Load capacity of 280 kg
• With handlebar loops
• With rubberized hooks on both belt ends
• 2 units

• Spring-mounted, 20° rotational movement possible towards front and rear
• More control and grip in the corners thanks to the maneuverability
• Large tread surface area of 60 mm
• Simpler and quicker weight shifting
• Simpler gear changing and braking
• Permanent contact between boot and foot pegs: extends the service life of your boots!

• Made from polyester, with special rubberized back
• Gas and oil resistant
• In special KTM design
• Size: 100 x 170 cm

• Ratchet (with locking device), lever, two extensions and socket wrench
• Hexagon sockets from 4 to 14
• Allen keys from 3 to 8
• Phillips, slotted and Torx bits

• Ratchet (with locking device), lever, two extensions and socket wrench
• Hexagon sockets from 6 to 24
• Allen keys from 3 to 10
• Phillips and slotted bits
• Torx bits from 15 to 55

• The Z-ring or X-ring has 4 contact points in contrast to 2 contact points with the O-ring version
• This means higher flexibility and better running characteristics for the Z-ring or X-ring chain
• The spring effect of the Z-ring or X-ring guarantees consistent and permanent lubrication
• This means a significantly longer service life for the Z-ring or X-ring chain
• The Z-ring or X-ring provides a better seal against penetration by water and dirt

• Manufactured from carbon
• Optimum protection against stone impacts
• Can be installed on brake caliper supports 79613975044, 7771397501030, 7771397511030, 78113975044, 78113975144, 78113975244, 78913975044 or 78913975144

• Floating brake disc manufactured from special high-grade stainless steel
• Internal ring made from high-grade aluminum
• With Flame design for added braking performance
• Minimal wear on brake linings

• Floating brake disc manufactured from special high-grade stainless steel
• With wave design for added braking performance
• Minimal wear on brake linings
• The front brake caliper mounting kit 72009960044 is required for mounting

Prevents twigs being caught between the engine and the foot brake lever and the foot brake lever being bent or blocked by this.

• Made of carbon
• Optimum protection against roost
• Made to fit all 48 mm forks

• The Z-ring or X-ring has 4 contact points in contrast to 2 contact points with the O-ring version
• This means higher flexibility and better running characteristics for the Z-ring or X-ring chain
• The spring effect of the Z-ring or X-ring guarantees consistent and permanent lubrication
• This means a significantly longer service life for the Z-ring or X-ring chain
• The Z-ring or X-ring provides a better seal against penetration by water and dirt

• higher flexibility and better running characteristics
• consistent and permanent lubrication
• better seal against water and dirt
• significantly longer service life

This rear sprocket not only looks cool, it also provides the following compelling benefits:

• Manufactured from high-strength 7075-T6 aluminium, the strongest aluminium in the world
• The chain runs smoothly, straight as a die and true, because it's ground level to an accuracy of 0.002 mm
• No small stones or dirt particles can become stuck under the chain thanks to angled recesses between the teeth
• All these properties mean lower wear and extreme durability
• Orange anodised with a permanent, organic and environmentally friendly pigment

Use of the 50T rear sprocket as of MY 14 can lead to space problems with the chainguide fitted as standard. If this is the case, then chainguide 773.04.070.310 must be used.

Ingenious: Foot pegs that move with you when you shift your weight. Ideal for Motocross, Enduro and Supermoto.

The benefits:

• Spring-mounted, 20-degree rotational movement possible towards front and rear
• More control and grip in the corners thanks to the maneuverability
• Large tread surface of 60 mm
• Simpler and quicker weight shifting
• Simpler gear changing and braking
• Permanent contact between boot and foot peg: extends the service life of your boots!

• Ergonomic; contour matched to the shape of the hand for maximum comfort
• Small "half waffle" ribs on the rear for secure grip
• Made from two materials with different grades of hardness
• Three areas for the metal safety wire
• Grip hardness: medium

• Ergonomic; contour matched to the shape of the hand for maximum comfort
• Small "half waffle" ribs on the rear for secure grip
• Made from two materials with different grades of hardness
• Three areas for the metal safety wire
• Grip hardness: soft

• Harder orange material on the inside and at the grip ends for a long service life
• Softer black material on the outside, where the hand lies on the grip, for increased comfort
• With open grip ends for closed handguards or bar ends

• Harder orange material on the inside and at the grip ends for a long service life
• Softer black material on the outside, where the hand lies on the grip, for increased comfort

• High-strength nylon strap
• Indispensable for use on extreme terrain
• Attaches to fork tube

This handguard set is not just visually impressive. Thanks to the special mix of materials, the handguard protects your hands and controls from damage without immediately breaking up. They also give you outstanding weather protection.

This handguard set is not just visually impressive. Thanks to the special mix of materials, the handguard protects your hands and controls from damage without immediately breaking up. They also give you outstanding weather protection.

This handguard set is not just visually impressive. Thanks to the special mix of materials, the handguard protects your hands and controls from damage without immediately breaking up. They also give you outstanding weather protection.

This handguard set has been specially developed for your motorcycle and is an essential accessory for heavy-duty offroad and Supermoto sessions. The broad, generous proportions, combined with the robust aluminum external frame ensure good mobility together with maximum protection in the event of a collision, stones thrown up from the road, branches etc.

• 78002079100EB is mounted standard on the 790 Adventure R
  

• Black center section = maximum strength for optimum protection
• Coloured upper and lower parts = highly flexible for enduring the roughest of treatment
• The choice is yours: attached directly to the handlebar with a plastic bracket or directly to the lever mounting with a special adaptor.
• Cannot be fitted with Twinwall handlebar.

Attached directly at the levers with a special mounting.

• Black center section = maximum strength for optimum protection
• Coloured upper and lower parts = highly flexible for enduring the roughest of treatment
• The choice is yours: attached directly to the handlebar with a plastic bracket or directly to the lever mounting with a special adaptor
• Cannot be fitted with Twinwall handlebar

Attached directly at the levers with a special mounting.

• Open version
• Manufactured with two-component injection molding technology
• Black mid-section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible, enduring even the roughest of treatment
• Attached directly at the levers with a special mounting.

• Open version
• Manufactured with two-component injection molding technology
• Black mid-section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible, enduring even the roughest of treatment
• Attached directly at the levers with a special mounting.

• Never again cold fingers!
• Mounting over handlebar and switches
• Better control during winter ride-outs

• Cushioning of heavy knocks
• Absorption of vibration from chassis and engine
• Additional handlebar damping in horizontal direction
• Optimum steering precision
• Handlebar height adjustable to 2 positions
• Further damping elements available in three degrees of hardness (soft, medium, hard) for individual tuning

• All KTM handlebars are made from EN AW 7010 T6 aluminum
• 28.5 mm diameter in the clamping area
• 22.15 mm diameter in the lever area
• Position markings for simple setting
• Dimensions: A = 115 mm, B = 806 mm, C = 62 mm

Dimensions: A = 79 mm, B = 811 mm, C = 74 mm

Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

• Including plastic insert
• The brake or clutch armature rotates in case of a fall
• Reduces the risk of a lever being broken
• Suitable for all Brembo® and Formula brake and clutch assembles

Provides optimum protection. With the integrated card holder you always have the time in view. A small extra pocket allows you to stow small items. Can also be fitted in combination with the PHDS-handlebar support.

00050000929 handle bar support kit required for use on MY16 and on XC from MY16.

• Extremely low weight
• Sensitive feedback behavior
• High speed setting
• Optimum 25 click setting range

Proven success with the KTM Works Rally Team. Fits all SX and EXC models.

Medium-strength thread lock. Suitable for all metal thread connections.

Medium strength thread lock - contents, 50 ml.

• Temperature resistant from -55 to +200 °C 
• Fills gaps up to 0.25 mm
• Final strength achieved after 1 to 3 hours
  

• Waterproof resistant coating
• Waterproof roll closure

• Suitable for all KTM GPS holders
• Size: 170 x 130 x 35 mm

Only for use on original handlebar mounting.

• Universal and discreet mounting solution for your smartphone
• Counterpart for the smartphone cases.
• The smartphone can be easily mounted on the motorcycle by turning it 90°.
• Can be clamped on the handlebar (including different adaptor)
• The arm can be rotated in any position for the perfect position for your smartphone.

• Protects your expensive smartphone and still keeping a slim design
• Integrated counterpart for the smartphone bracket
• The smartphone can be easily mounted on the motorcycle by turning it 90°

• Unobtrusive protection for your expensive smartphone
• Integrated counterpart for the smartphone bracket
• The smartphone can easily be mounted on the bracket by turning it 90°.

• Unobtrusive protection for your expensive smartphone
• Integrated counterpart for the smartphone bracket
• The smartphone can easily be mounted on the bracket by turning it 90°.

• Unobtrusive protection for your expensive smartphone
• Integrated counterpart for the smartphone bracket
• The smartphone can easily be mounted on the bracket by turning it 90°.

• Protects your expensive smartphone and still keeping a slim design
• Integrated counterpart for the smartphone bracket
• The smartphone can be easily mounted on the motorcycle by turning it 90°

• Protects your expensive smartphone and still keeping a slim design
• Integrated counterpart for the smartphone bracket
• The smartphone can be easily mounted on the motorcycle by turning it 90°

• Unobtrusive protection for your expensive smartphone
• Integrated counterpart for the smartphone bracket
• The smartphone can easily be mounted on the bracket by turning it 90°.

• Unobtrusive protection for your expensive smartphone
• Integrated counterpart for the smartphone bracket
• The smartphone can easily be mounted on the bracket by turning it 90°.

• Can be stuck on any flat surface (rear side of smartphone, or smartphone case)
• Integrated counterpart for the smartphone bracket
• The smartphone can be easily mounted on the motorcycle by turning it 90°
• Dimensions: 66x55mm (2.6x2.17 inch)

• Made from neoprene
• Ideal protection for sealing the fork
• For use with the open fork protector
• For fork tube with a diameter of 43 mm

• Two different heights possible
• Can be used as a stand for the quickfill system
• Storage space for the front and rear axle when removing the wheels
• Attachments for the following parts: mud removal tool, exhaust plug, magnetic bolt pan and various tools

Tool for lifting the motorcycle.

Stroke: 260/370 mm
Maximum load:  150 kg

• Easy handling and operation
• More safety
• Less wear on the cord
• Made of high quality material
• Cable not included

Patented gage for three important checks:

• Check and adjust chain tension
• Check chain lengthening (wear)
• Check positioning of rear wheel axle

• Contents are in accordance with DIN standard 13167-2014 for motorcyclists
• Waterproof packaging
• With its slim shape and Velcro straps at the back, the first aid kit is easy to store

Note:

It is mandatory to carry a first aid kit in many countries (such as Austria, Italy, Portugal and Spain).

The optimum solution for always having the most important tools to hand when on the road.

• Ratchet (with locking device), lever, two extensions and socket wrench
• Hexagon sockets from 6 to 24
• Allen keys from 3 to 10
• Phillips and slotted bits
• Torx bits from 15 to 55

• Ratchet (with locking device), lever, two extensions and socket wrench
• Hexagon sockets from 4 to 14
• Allen keys from 3 to 8
• Phillips, slotted and Torx bits

• Push-on spoke wrenches in sizes 5.65 and 6.95 mm
• Push-on ratchet ¼"
• Ratchet attachments: 6, 8, 10 mm socket wrench, 15 Torx

• Stabilizes your motorcycle during transportation
• Protects the fork shaft seal rings and fork springs from damage due to overly strong tightening down with lashing straps while transportation
• Gets clamped in between the tyre and the bottom of the front wheel fender

• Enables secure attachment to the machine without scratching your handlebars or tank
• With rubberized hooks and handlebar loops on belt ends
• 2 units

• Enables secure attachment to the machine without scratching your handlebars or tank
• Made from durable ballistic nylon
• Load capacity of 280 kg
• With handlebar loops
• With rubberized hooks on both belt ends

• Enables secure fastening to the machine without scratching your handlebars or tank
• Made from durable ballistic nylon
• Load capacity of 280 kg
• With handlebar loops
• With a rubberized hook and a carabiner on the belt ends
• 2 units

• Made from polyester, with special rubberized back
• Gas and oil resistant
• In special KTM design
• Size: 100 x 170 cm

• 10 pcs. cleanig towels, packed separately
• towel size 285 x 200 mm
• 70% Isopropanol
• ideal for cleaning of surfaces before application of stickers

• Extra thick film
• Protects the outer tubes against stone impact

• For wheel size 18/21"; 19/21"
• Pre-cut sticker
• Suitable for front and rear rim

• For wheel size 18/21"; 19/21"
• Pre-cut sticker
• Suitable for front and rear rim

This drive kit consists of a 11 tooth front and a black 48 tooth rear sprocket wheel, a DID chain and master link.

HeliCoil plus

Spark plug thread repair selection M10x1 / M12x1.25 / M14x1.25.